MoCA object that contains the {{object|Interface}} table {{bibref|MoCAv1.0}} {{bibref|MoCAv1.1}}. {{numentries}} MoCA interface table (a stackable interface object as described in {{bibref|TR-181i2|Section 4.2}}). Each table entry models the PHY and MAC levels of a MoCA interface {{bibref|MoCAv1.0}} {{bibref|MoCAv1.1}}. Enables or disables the interface. This parameter is based on ''ifAdminStatus'' from {{bibref|RFC2863}}. The current operational state of the interface (see {{bibref|TR-181i2|Section 4.2.2}}). {{enum}} When {{param|Enable}} is {{false}} then {{param}} SHOULD normally be {{enum|Down}} (or {{enum|NotPresent}} or {{enum|Error}} if there is a fault condition on the interface). When {{param|Enable}} is changed to {{true}} then {{param}} SHOULD change to {{enum|Up}} if and only if the interface is able to transmit and receive network traffic; it SHOULD change to {{enum|Dormant}} if and only if the interface is operable but is waiting for external actions before it can transmit and receive network traffic (and subsequently change to {{enum|Up}} if still operable when the expected actions have completed); it SHOULD change to {{enum|LowerLayerDown}} if and only if the interface is prevented from entering the {{enum|Up}} state because one or more of the interfaces beneath it is down; it SHOULD remain in the {{enum|Error}} state if there is an error or other fault condition detected on the interface; it SHOULD remain in the {{enum|NotPresent}} state if the interface has missing (typically hardware) components; it SHOULD change to {{enum|Unknown}} if the state of the interface can not be determined for some reason. This parameter is based on ''ifOperStatus'' from {{bibref|RFC2863}}. {{datatype|expand}} The textual name of the interface as assigned by the CPE. The accumulated time in {{units}} since the interface entered its current operational state. {{list}} {{reference|an interface object that is stacked immediately below this interface object}} See {{bibref|TR-181i2|Section 4.2.1}}. Note: Since {{object}} is a layer 1 interface, it is expected that {{param}} will not be used. Indicates whether the interface points towards the Internet ({{true}}) or towards End Devices ({{false}}). For example: * For an Internet Gateway Device, {{param}} will be {{true}} for all WAN interfaces and {{false}} for all LAN interfaces. * For a standalone WiFi Access Point that is connected via Ethernet to an Internet Gateway Device, {{param}} will be {{true}} for the Ethernet interface and {{false}} for the WiFi Radio interface. * For an End Device, {{param}} will be {{true}} for all interfaces. The MAC Address of the interface. Note: This is not necessarily the same as the Ethernet header source or destination MAC address, which is associated with the IP interface and is modeled via the {{param|.Ethernet.Link.{i}.MACAddress}} parameter. This interface's firmware version. This parameter is based on ''mocaIfSoftwareVersion'' from {{bibref|MOCA11-MIB}}. The maximum MoCA PHY bit rate (expressed in {{units}}). The maximum bandwidth of this interface for flows onto the MoCA network in {{units}}. This parameter is based on ''mocaIfMaxIngressNodeBw'' from {{bibref|MOCA11-MIB}}. The maximum bandwidth of this interface for flows from the MoCA network in {{units}}. This parameter is based on ''mocaIfMaxEgressNodeBw'' from {{bibref|MOCA11-MIB}}. Identifies the highest MoCA version that this interface supports. This element MUST be in the form of dot-delimited integers, where each successive integer represents a more minor category of variation. For example, 1.0, where the components mean major.minor revision number. {{pattern}} This parameter is based on ''mocaIfMocaVersion'' from {{bibref|MOCA11-MIB}}. Identifies the MoCA version that the MoCA network is currently running. This element MUST be in the form of dot-delimited integers, where each successive integer represents a more minor category of variation. For example, 1.0, where the components mean major.minor revision number. {{pattern}} This parameter is based on ''mocaIfNetworkVersion'' from {{bibref|MOCA11-MIB}}. The Node ID of the current Network Coordinator (NC) for the MoCA network. This parameter is based on ''mocaIfNC'' from {{bibref|MOCA11-MIB}}. The Node ID of this interface. This parameter is based on ''mocaIfNodeID'' from {{bibref|MOCA11-MIB}}. The maximum network node capability supported by the interface. If {{param}} is {{true}} then the interface supports 16 nodes (the maximum for a MoCA 1.1 network). If {{param}} is false then the interface supports 8 nodes (the maximum for a MoCA 1.0 network). Whether this interface is a preferred Network Coordinator (NC). This parameter is based on ''mocaIfPreferredNC'' from {{bibref|MOCA11-MIB}}. The Node ID of the backup Network Coordinator node. This parameter is based on ''mocaIfBackupNC'' from {{bibref|MOCA11-MIB}}. The configured privacy mode. This indicates whether link-layer security is enabled ({{true}}) or disabled ({{false}}) for network admission. The configured privacy setting MAY NOT match the current operational state ({{param|PrivacyEnabled}}), since this setting is only applied during network formation or admission. Indicates whether link-layer security is enabled or disabled. This parameter is based on ''mocaIfPrivacyEnable'' from {{bibref|MOCA11-MIB}}. Hexadecimal encoded 64-bit mask of supported frequencies. This is the bit map of the spectrum that the interface supports, and each bit represents 25 MHz of spectrum. The least significant bit of the rightmost character corresponds to 800MHz, which is the lowest frequency. For example, an interface that supports 1150 MHz through 1500 MHz would have a value of 0x000000001FFFC000. This parameter is based on ''mocaIfCapabilityMask'' from {{bibref|MOCA11-MIB}}. The configured hexadecimal encoded 64-bit mask of enabled frequencies for network admission. The configured frequencies MAY NOT match the current operational state ({{param|FreqCurrentMask}}), since this setting is only applied during network formation or admission. Hexadecimal encoded 64-bit mask of used frequencies. This is the bit map of the spectrum that can be used and is a subset of the {{param|FreqCapabilityMask}}. Each bit represents 25 MHz of spectrum. The least significant bit of the rightmost character corresponds to 800MHz, which is the lowest frequency. This parameter is based on ''mocaIfChannelMask'' from {{bibref|MOCA11-MIB}}. Current Operational Frequency. The RF frequency in Hz to which the MoCA interface is currently tuned. This parameter is only valid when {{param|Status}} is {{enum|Up|Status}}. This parameter is based on ''mocaIfRFChannel'' from {{bibref|MOCA11-MIB}}. Last Operational Frequency. The RF frequency in Hz to which the MoCA interface was tuned when last in the {{enum|Up|Status}} state. This parameter is based on ''mocaIfLOF'' from {{bibref|MOCA11-MIB}}. MoCA Password. The value consists of numeric characters (0-9). {{pattern}} This parameter is based on ''mocaIfPassword'' from {{bibref|MOCA11-MIB}}. Transmit Power attenuation in dB relative to the maximum transmit power. The MoCA interface SHOULD have {{param|Enable}} set to {{false}} for any change in this configuration. If the parameter is modified when {{param|Enable}} is {{true}} then this change might take several minutes to complete. This parameter is based on ''mocaIfTxPowerLimit'' from {{bibref|MOCA11-MIB}}. Target PHY rate in Mbps for the power control algorithm. The MoCA interface SHOULD have {{param|Enable}} set to {{false}} for any change in this configuration. If the parameter is modified when {{param|Enable}} is {{true}} then this change might take several minutes to complete. This parameter is based on ''mocaIfPowerControlTargetRate'' from {{bibref|MOCA11-MIB}}. Beacon Transmit Power attenuation in {{units}} relative to the maximum transmit power. The MoCA interface SHOULD have {{param|Enable}} set to {{false}} for any change in this configuration. If the parameter is modified when {{param|Enable}} is {{true}} then this change might take several minutes to complete. This parameter is based on ''mocaIfBeaconPowerLimit'' from {{bibref|MOCA11-MIB}}. Hexadecimal encoded 64-bit mask of MoCA taboo channels identified for the home network. This is the bit map of the spectrum that the interface supports, and each bit represents 25 MHz of spectrum. The least significant bit of the rightmost character corresponds to 800MHz, which is the lowest frequency. This parameter is based on ''mocaIfTabooChannelMask'' from {{bibref|MOCA11-MIB}}. Hexadecimal encoded 64-bit mask of supported frequencies. This is the bit map of the spectrum that the interface supports, and each bit represents 25 MHz of spectrum. The least significant bit of the rightmost character corresponds to 800MHz, which is the lowest frequency. This parameter is based on ''mocaIfNodeTabooChannelMask'' from {{bibref|MOCA11-MIB}}. The broadcast PHY transmit rate in {{units}} for this interface. This parameter is based on ''mocaIfTxGcdRate'' from {{bibref|MOCA11-MIB}}. Transmit Power attenuation in {{units}} relative to the maximum transmit power for broadcast transmissions. This parameter is based on ''mocaIfTxGcdPowerReduction'' from {{bibref|MOCA11-MIB}}. Whether this interface supports the 256 QAM feature. This parameter is based on ''mocaIfQAM256Capable'' from {{bibref|MOCA11-MIB}}. The packet aggregation capability supported by the interface. Standard values are 0 (no support), 6 (6 {{units}}) or 10 (10 {{units}}). This parameter is based on ''mocaIfPacketsAggrCapability'' from {{bibref|MOCA11-MIB}}. {{numentries}} Throughput statistics for this interface. The CPE MUST reset the interface's Stats parameters (unless otherwise stated in individual object or parameter descriptions) either when the interface becomes operationally down due to a previous administrative down (i.e. the interface's {{param|#.Status}} parameter transitions to a down state after the interface is disabled) or when the interface becomes administratively up (i.e. the interface's {{param|#.Enable}} parameter transitions from {{false}} to {{true}}). Administrative and operational interface status is discussed in {{bibref|TR-181i2|section 4.2.2}}. The total number of bytes transmitted out of the interface, including framing characters. The total number of bytes received on the interface, including framing characters. The total number of packets transmitted out of the interface. The total number of packets received on the interface. The total number of outbound packets that could not be transmitted because of errors. The total number of inbound packets that contained errors preventing them from being delivered to a higher-layer protocol. The total number of packets requested for transmission which were not addressed to a multicast or broadcast address at this layer, including those that were discarded or not sent. The total number of received packets, delivered by this layer to a higher layer, which were not addressed to a multicast or broadcast address at this layer. The total number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. The total number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being delivered. One possible reason for discarding such a packet could be to free up buffer space. The total number of packets that higher-level protocols requested for transmission and which were addressed to a multicast address at this layer, including those that were discarded or not sent. The total number of received packets, delivered by this layer to a higher layer, which were addressed to a multicast address at this layer. The total number of packets that higher-level protocols requested for transmission and which were addressed to a broadcast address at this layer, including those that were discarded or not sent. The total number of received packets, delivered by this layer to a higher layer, which were addressed to a broadcast address at this layer. The total number of packets received via the interface which were discarded because of an unknown or unsupported protocol. The QoS object provides information on MoCA parameterized QoS for this interface {{bibref|MoCAv1.1}}. The number of QoS flows that this interface has from the MoCA network. This parameter is based on ''mocaIfEgressNodeNumFlows'' from {{bibref|MOCA11-MIB}}. The number of QoS flows that this interface has onto the MoCA network. This parameter is based on ''mocaIfIngressNodeNumFlows'' from {{bibref|MOCA11-MIB}}. {{numentries}} The flow statistics table provides information on the MoCA parameterized QoS flows this interface has allocated onto the MoCA network. The flow ID used to identify a flow in the network. This parameter is based on ''mocaIfFlowID'' from {{bibref|MOCA11-MIB}}. The Destination Address (DA) for the packets in this flow. This parameter is based on ''mocaIfPacketDA'' from {{bibref|MOCA11-MIB}}. Maximum required rate in {{units}}. This parameter is based on ''mocaIfPeakDataRate'' from {{bibref|MOCA11-MIB}}. Maximum burst size. This parameter is based on ''mocaIfBurstSize'' from {{bibref|MOCA11-MIB}}. Flow lease time (expressed in {{units}}). A {{param}} of 0 means unlimited lease time. This parameter is based on ''mocaIfLeaseTime'' from {{bibref|MOCA11-MIB}}. Flow lease time remaining (expressed in {{units}}). If {{param|LeaseTime}} is 0 then a {{param}} of 0 means unlimited lease time; otherwise, a {{param}} of 0 means expired. This parameter is based on ''mocaIfLeaseTimeLeft'' from {{bibref|MOCA11-MIB}}. The number of packets transmitted for this flow. This parameter is based on ''mocaIfTxPacketsFlow'' from {{bibref|MOCA11-MIB}}. This table contains information about other MoCA devices currently associated with this MoCA interface. The MAC address of the associated device's MoCA interface. The Node ID of this remote device. This parameter is based on ''mocaNodeIndex'' from {{bibref|MOCA11-MIB}}. Whether this remote device is a preferred Network Coordinator (NC). This parameter is based on ''mocaNodePreferredNC'' from {{bibref|MOCA11-MIB}}. Identifies the highest MoCA version that this remote device supports. This element MUST be in the form of dot-delimited integers, where each successive integer represents a more minor category of variation. For example, 1.0, where the components mean major.minor revision number. {{pattern}} This parameter is based on ''mocaNodeMocaVersion'' from {{bibref|MOCA11-MIB}}. The PHY transmit rate (in {{units}}) to this remote device. This parameter is based on ''mocaMeshTxRate'' from {{bibref|MOCA11-MIB}}. The PHY receive rate (in {{units}}) from this remote device. The reduction in transmitter level (in {{units}}) due to power control. This parameter is based on ''mocaNodeTxPowerReduction'' from {{bibref|MOCA11-MIB}}. The power level (in {{units}}) received at the MoCA interface from this remote device. This parameter is based on ''mocaNodeRxPower'' from {{bibref|MOCA11-MIB}}. The broadcast PHY transmit rate (in {{units}}) from this remote device. This parameter is based on ''mocaNodeTxGcdRate'' from {{bibref|MOCA11-MIB}}. The power level (in {{units}}) received at the MoCA interface from this remote device. This parameter is based on ''mocaNodeRxGcdPower'' from {{bibref|MOCA11-MIB}}. The number of packets transmitted to this remote device (Note: Includes Broadcast, Multicast and Unicast packets). The number of packets received from this remote device (Note: Includes Broadcast, Multicast and Unicast packets). This parameter is based on ''mocaNodeRxPackets'' from {{bibref|MOCA11-MIB}}. The number of errored and missed packets received from this remote device. This parameter is based on ''mocaNodeRxDrops'' from {{bibref|MOCA11-MIB}}. Whether this remote device supports the 256 QAM feature. This parameter is based on ''mocaNodeQAM256Capable'' from {{bibref|MOCA11-MIB}}. The packet aggregation capability supported by the remote device. Standard values are 0 (no support), 6 (6 {{units}}) or 10 (10 {{units}}). This parameter is based on ''mocaNodePacketsAggrCapability'' from {{bibref|MOCA11-MIB}}. The signal to noise level (in {{units}}) received at this interface from this remote device. This parameter is based on ''mocaNodeSNR'' from {{bibref|MOCA11-MIB}}. Whether or not this remote device is currently present in the MoCA network. The ability to list inactive nodes is OPTIONAL. If the CPE includes inactive nodes in this table, {{param}} MUST be set to {{false}} for each inactive node. The length of time an inactive node remains listed in this table is a local matter to the CPE.