The Operating Classes for which this channel scan is requested. The Operating Class per {{bibref|802.11-2020|Table E-4}} of the OpClass and Channel tuple scanned by the Radio. Note that the Operating Class identifies the band and channel width. For 2.4GHz and 5GHz bands, only 20MHz Operating Classes are valid. The Channels for which this channel scan is requested. The Channel number of the Channel that is requested to be scanned. The duration of the time to scan each channel in {{units}}. A value of 50 {{units}} is suggested. The duration of time to scan each Dynamic Frequency Selection (DFS) channel in {{units}}. A value of at least one beacon interval, typically 100 {{units}}, is suggested. The time in {{units}} after which the driver has to go back to the original channel before scanning the next channel to avoid disruption. If this is omitted, or is not supported by the device, then it should be ignored. The Service Set Identifier (SSID) to scan. If omitted, then all SSIDs are scanned. Basic Service Set Identifier (BSSID) of the target BSS which the associated device(s) is to be associated to. The number of the Wi-Fi channel the backhaul BSS is to be associated to. If {{param}} is not specified, then the radio is to determine which channel to use to associate to the requested {{param|TargetBSS}}. The maximum timeout for this backhaul steering to occur in {{units}}. Indicates if the disassociation is imminent, as defined in {{bibref|802.11-2020|Section 9.6.13.9}}. The number of {{units}} until the AP sends a disassociation frame to this station. If {{param}}=0 then {{param}} is not used. The number of {{units}} for which the BSS is not present. If {{param}}=0 or if this input in not provided, then {{param}} is not used. The amount of time in {{units}} that the {{command}} is valid for. If {{param}}=0 or if this input in not provided, then {{param}} is not used. The amount of time in {{units}} that this associated device is not allowed to return to the original BSS. If {{param}}=0 or if this input in not provided, then {{param}} is not used. BSSID of the target BSS which the associated device(s) is to be associated to. The time for which the associated device is to be disassociated in {{units}}. If set to 0, then the associated device is blocked indefinately. The reason code for the request for the associated device to be disassociated, as defined in {{bibref|802.11-2020|Table 9-49}}. An optional input, if true then this is a request for a Silent Disassociate, whereby the AP is to remove the station from its list of associated devices without sending a message to the station. If this input in not provided, then a value of {{false}} is assumed. This command allows or disallows EasyMesh traffic separation {{bibref|EasyMesh|Section 19.1}}. If {{param|Enable}} is {{true}} then the parameters defining traffic separation details can also be input with this command. This command applies to all EasyMesh Agent devices in the Wi-Fi network. This command can configure {{object|#.Device.{i}.SSIDtoVIDMapping.{i}.}} and {{param|#.Device.{i}.TrafficSeparationAllowed}}. Status is to be returned after implementation or failed implementation on all agents/devices/APs in this Multi-AP network. : {{true}}: EasyMesh traffic separation is allowed. : {{false}}: EasyMesh traffic separation is not allowed. The Service Set Identifier (SSID) to VLAN ID (VID) mapping for EasyMesh traffic separation {{bibref|EasyMesh}}. Consists of a table of pairs of {{param|SSID}} and corresponding {{param|VID}}. If this input is not provided, then existing {{object|##.Device.{i}.SSIDtoVIDMapping.{i}.}} apply. The SSID name. The VLAN ID (VID). Indicates the type of outcome of the request to allow or disallow EasyMesh traffic separation. {{enum}} Indicates successful implementation on all agents/devices/APs in this Multi-AP network. This command allows or disallows EasyMesh service prioritization {{bibref|EasyMesh|Section 20}}. If {{param|Enable}} is {{true}} then the parameters defining service prioritization details can also be input with this command. This command can configure {{object|#.Device.{i}.SPRule.{i}.}}, {{param|#.Device.{i}.DSCPMap}} and {{param|#.Device.{i}.ServicePrioritizationAllowed}}. This command applies to all EasyMesh Agent devices in the Wi-Fi network. Status is to be returned after implementation or failed implementation on all agents/devices/APs in this Multi-AP network. : {{true}}: EasyMesh service prioritization is allowed. : {{false}}: EasyMesh service prioritization is not allowed. This object describes a list of service prioritization (SP) rules {{bibref|EasyMesh}}. If this input is not provided, then existing {{object|##.Device.{i}.SPRule.{i}.}} apply. Service prioritization rule Identifier. Rule Precedence - higher number means higher priority. Rule Output. The value of, or method used to select the 802.1Q C-TAG Priority Code Point (PCP) output value. Indicates if the rule always matches. A hexadecimal string of 64 PCP values (one octet per value) corresponding to the DSCP markings 0x00 to 0x3F, ordered by increasing DSCP value. Each octet is in the range 0x00 - 0x07. This is used to select a PCP value if a Service Prioritization Rule specifies Rule Output: 0x08. If this input is not provided, then the existing {{param|#.Device.{i}.DSCPMap}} applies. Indicates the type of outcome of the request to allow or disallow EasyMesh service prioritization. {{enum}} Indicates successful implementation on all agents/devices/APs in this Multi-AP network Request to initiate a channel scan. The operating classes, and list of channels for each operating class, are input. If no operating class is provided to the input, then all available opclasses and channels are to be scanned. For 2.4GHz and 5GHz bands, only 20MHz operating classes are valid inputs. This command should result in updating {{object|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.ScanResult.}} The Operating Class per {{bibref|802.11-2020|Table E-4}}. For 2.4GHz and 5GHz bands, only 20MHz Operating Classes are valid. If this input is not provided, then all available opclasses and channels are to be scanned. Note that the operating class identifies the band, and channel width. The channel numbers in this Operating Class for which the request to initiate a channel scan applies. Indicates the type of scan to perform. If this is omitted, or is not supported by the device, then it should be ignored. {{enum}} The duration of the time to scan each channel in {{units}}. A value of 50 {{units}} is suggested. If this is omitted, or is not supported by the device, then it should be ignored. The duration of time to scan each Dynamic Frequency Selection (DFS) channel in {{units}}. Note that this is the time to scan the channel, and is not the time to perform DFS. A value of at least one beacon interval, typically 100 {{units}}, is suggested. If this is omitted, or is not supported by the device, then it should be ignored. The time in {{units}} after which the driver has to go back to the original channel before scanning the next channel to avoid disruption. If this is omitted, or is not supported by the device, then it should be ignored. Indicates the type of outcome of the request to initiate a channel scan. {{enum}} Request to enable or disable this radio. This command can result in updating {{param|Enabled}}. If the instance of this {{object}} is the same as {{object|Device.WiFi.Radio.{i}.}}, then this command has the same effect as writing to {{param|Device.WiFi.Radio.{i}.Enable}}. : {{true}}: this radio is to be enabled. : {{false}}: this radio is to be disabled. Indicates the type of outcome of the request to enable or disable this radio. {{enum}} Request a restart of the Wi-Fi subsystem. Indicates the type of outcome of the request to restart the Wi-Fi subsystem. {{enum}} Disallow or allow EasyMesh {{bibref|EasyMesh}} controller-initiated station (STA) steering on this device. This command can configure {{param|STASteeringState}}. : {{true}}: EasyMesh controller-initiated station steering disallowed; : {{false}}: EasyMesh controller-initiated station steering allowed. Indicates the type of outcome of the request to allow or disallow EasyMesh controller-initiated station steering. {{enum}} This command sets the upper limit on transmit power {{param|TransmitPowerLimit}} for this radio and {{param|OperatingClass}}. This command can configure {{param|#.CurrentOperatingClassProfile.{i}.TransmitPowerLimit}}. This is the upper limit on nominal transmit Equivalent Isotropically Radiated Power (EIRP) that this radio can use for the {{param|OperatingClass}}. In units of decibels relative to 1 mW {{units}}. The Operating Class per {{bibref|802.11-2020|Table E-4}} of the radio. Note that the Operating Class identifies the band and channel width. Indicates the type of outcome of the request to set a transmit power limit. {{enum}} {{numentries}} This object specifies the preferred backhaul links as populated by {{command|#.SetPreferredBackhauls()}}. The MAC address of the BSS, or APMLD, or similar Ethernet interface, on this preferred backhaul link. The MAC address of the backhaul Station STA (bSTA), or bSTAMLD, or similar Ethernet interface, on this preferred backhaul link. This command sets preferred backhaul links for EasyMesh {{bibref|EasyMesh}} backhaul. Indicates preferred backhaul links for EasyMesh {{bibref|EasyMesh}} backhaul. Consists of a table of pairs of MAC addresses. For a WI-Fi connection pair, an entry contains the BSSID and bSTA MAC address. For a wired connection pair, an entry contains the interface MAC addresses. This command applies to all EasyMesh Agent devices in the Wi-Fi network. Status is to be returned after implementation or failed implementation on all agents/devices/APs in this Multi-AP network. The MAC address of the BSS, or similar Ethernet interface, on this preferred backhaul link. The MAC address of the backhaul STA (bSTA), or similar Ethernet interface, on this preferred backhaul link. Indicates the type of outcome of the request to set preferred backhaul links. {{enum}} Indicates successful implementation of all preferred backhaul links in this Multi-AP network. This command specifies an {{param|SSID}} for use across this Wi-Fi Multi-AP network, or on this single-AP. Also specifies the {{param|PassPhrase}}, whether to add or remove this SSID, and specifies the {{param|Band}} for each {{param|SSID}}. This command applies to all EasyMesh Agent devices in the Wi-Fi network, or to this AP in the single-AP case. This command can be used to change any input parameter(s) if {{param|AddRemoveChange}} is set to {{enum|Change|AddRemoveChange}}. This command can configure {{object|#.SSID.{i}}}. Note that VLAN IDs (VIDs) can be configured per SSID with {{object|#.Device.{i}.SSIDtoVIDMapping.{i}}}. Status is to be returned after implementation or failed implementation on all agents/devices/APs in this Multi-AP network. The SSID for fronthaul use across this Wi-Fi Multi-AP network. Enable or disable this {{param|SSID}}. Disable stops the use of this {{param|SSID}}, but the object is retained. : {{true}}: this {{param|SSID}} is to be enabled. : {{false}}: this {{param|SSID}} is to be disabled. Indicates whether to add, remove or change this {{param|SSID}}. {{enum}} Status is to be returned after implementation or failed implementation on all agents/devices/APs in this Multi-AP network. If set to {{enum|Change}}, then all input parameters for this {{param|SSID}} that do not have null values are to be changed. Add this SSID. Remove this SSID. Change this SSID. The WPA2 Passphrase and/or SAE password for this {{param|SSID}}. The band(s) for which this {{param|SSID}} applies. {{enum}} If this input is not provided, then a value of {{enum|All}} applies. Applies to all bands 2.4 GHz band The entire 5 GHz band The entire 6 GHz band 5 GHz UNII-1 band, 5.15 to 5.25 GHz 5 GHz UNII-2 band, 5.25 to 5.725 GHz 5 GHz UNII-3 band, 5.725 to 5.85 GHz 5 GHz UNII-4 band, 5.85 to 5.925 GHz 6 GHz UNII-5 band, 5.925 to 6.425 GHz 6 GHz UNII-6 band, 6.425 to 6.525 GHz 6 GHz UNII-7 band, 6.525 to 6.875 GHz 6 GHz UNII-8 band, 6.875 to 7.125 GHz {{list}} List items indicate Authentication and Key Management (AKM) suites/security modes allowed on this BSS. {{enum}} "psk" indicates one or more of the PSK and FT-PSK AKMs defined in {{bibref|802.11-2020|Table 9-151}} typically at least "00-0F-AC:2" for interoperability. "dpp" indicates one or more of the DPP and FT-DPP AKMs defined in {{bibref|EasyConnect|Section 8.4}}, typically at least "50-6F-9A:2" for interoperability. "sae" indicates one or more of the SAE and FT-SAE AKMs defined in {{bibref|802.11-2020|Table 9-151}} typically at least "00-0F-AC:8" for interoperability. "SuiteSelector" indicates an AKM suite selector, the value of which is indicated in {{param|SuiteSelector}}. AKM suite selector, the AKM suite selector (OUI and type) is encoded as a 4-octet hex-encoded value without internal delimiters, e.g. 506F9A02 {{bibref|802.11-2020|Table 9-151}}. This parameter applies if {{param|AKMsAllowed}} includes value "SuiteSelector". Indicates if the SSID is advertised in beacons, or not. : {{true}}: this {{param|SSID}} is to be advertised in beacons. : {{false}}: this {{param|SSID}} is not to be advertised in beacons. Management Frame Protection (MFP) configuration. {{enum}} The IEEE 802.11 mobility domain {{bibref|802.11-2020|Section 9.4.2.46}}. Indicates the use of this {{param|SSID}}. {{enum}} Indicates the type of outcome of the request to set the SSID. {{enum}} Indicates successful implementation on all agents/devices/APs in this Multi-AP network Enables/disables the use of Dynamic Frequency Selection (DFS) channels on this device. This command can configure {{param|#.DFSEnable}}. : {{true}}: the use of Dynamic Frequency Selection (DFS) channels is allowed; : {{false}}: the use of Dynamic Frequency Selection (DFS) channels is disallowed; Indicates the type of outcome of the request to allow or disallow the use of Dynamic Frequency Selection (DFS) channels. {{enum}} This command requests to set the Anticipated Channel Preference. The operating classes, and list of channels for each operating class, are input. The Operating Class per {{bibref|802.11-2020|Table E-4}}. Note that the operating class identifies the band and channel width. The channel numbers in this Operating Class. Indicates the type of outcome of the request to set the anticipated channel preference. {{enum}} This command disallows Mirrored Stream Classification Service (MSCS) service prioritization to particular STA(s). {{bibref|EasyMesh}} This command applies to all EasyMesh Agent devices in the Wi-Fi network. This command configures {{param|#.MSCSDisallowedStaList}}. List of STAs for which MSCS operation is disallowed. Indicates the type of outcome of the request to disallow MSCS service prioritization to particular STA(s) {{enum}} This command disallows Stream Classification Service (SCS) service prioritization to particular STA(s). {{bibref|EasyMesh}} This command applies to all EasyMesh Agent devices in the Wi-Fi network. This command can configure {{param|#.SCSDisallowedStaList}}. List of STAs for which SCS operation is disallowed. Indicates the type of outcome of the request to disallow SCS service prioritization to particular STA(s). {{enum}} This command configures each of the descriptor elements for Mirrored Stream Classification Service (MSCS), Stream Classification Service (SCS), or QoS Management. {{bibref|EasyMesh}}. This command can configure {{object|QMDescriptor.{i}.}}. If {{param|Input.QMDescriptor.{i}.DescriptorElement}} is for SCS or MSCS, the AP adds/changes/removes the rule according to the descriptor element request type. If a {{param|Input.QMDescriptor.{i}.DescriptorElement}} is a QoS Management DSCP Policy, the AP sends it to the STA identified by the {{param|Input.QMDescriptor.{i}.ClientMAC}}. This object contains a table of {{param|DescriptorElement}}. The BSSID of BSS for which this descriptor applies. MAC address of the Station (STA) for which this descriptor applies. The descriptor element. One of: : MSCS descriptor element (as described in {{bibref|802.11-2020|Section 9.4.2.243}}, or : SCS descriptor element (as described in {{bibref|802.11-2020|Section 9.4.2.121}}, or : QoS Management DSCP policy element (as described in {{bibref|802.11-2020|Section 9.4.2.94}} and {{bibref|RFC8325|Section 6.3}}). Indicates the type of outcome of the request to configure descriptor elements. {{enum}} This command sets the spatial reuse configuration of this radio. Applies only to Wi-Fi 6 and possibly later generations of radios. Acronyms: Spatial Reuse Group (SRG), Overlapping Basic Service Set (OBSS), Preamble Detection (PD). This command can configure {{object|#.SpatialReuse.}}. If some input parameter(s) are not provided, then the corresponding existing parameter in {{object|#.SpatialReuse.}} applies. Indicates the type of outcome of the request to set the spatial reuse configuration of this radio. {{enum}} Initiates an EasyMesh {{bibref|EasyMesh}} Controller initiated steering mandate request to steer a STA from one EasyMesh agent to another. The steering mechanism is determined by the EasyMesh controller. Application of BTM or non BTM steering, timing, failsafes, and command rejection are determined by the EasyMesh controller. The {{param|TargetBSSID}} should be an instance of a {{param|#.BSSID}}. Basic Service Set Identifier (BSSID) or AP MLD MAC Address of the target BSS which the associated device(s) is to be steered to. Wildcard BSSID is represented by FFFFFFFFFFFF. The request mode. {{enum}} Request is a Steering Opportunity, indicated by 0 in {{bibref|EasyMesh|Table 49}}. Request is a Steering Mandate to trigger steering for specific client STA(s), indicated by 1 in {{bibref|EasyMesh|Table 49}}. BTM disassociation imminent. BTM abridged. Link removal imminent. Time period in {{units}} (from reception of the Steering Request message) for which the request is valid. If {{param|RequestMode}} is Steering_Mandate, then this is ignored. Time period in {{units}} of the disassociation timer in the BTM Request. The Target BSS Operating Class per {{bibref|802.11-2020|Table E-4}}. If the {{param|TargetBSSID}} is set to "Wildcard BSSID", then this is ignored. Target BSS channel number for channel on which the Target BSS is transmitting Beacon frames. If the {{param|TargetBSSID}} is set to "Wildcard BSSID", then then this is ignored. Indicates the response to the Wi-Fi backhaul steering request. {{enum}} This command represents a request to initiate a full scan on this radio, including all channels supported by this radio, for a specific {{param|DwellTime}} and {{param|HomeTime}}. This command will result in updating {{object|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.ScanResult.}} If the instance of this {{object}} is the same as {{object|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}}}, then this command is similar to, {{command|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.ChannelScanRequest()}}. Indicates the type of outcome of the request to initiate a full band scan. {{enum}} This command represents a request to initiate a throughput (speed) test from a BSS to a STA. MAC address of the STA that the throughput test is to be run to. The VLAN ID (VID) that the throughput test is to run on. Wi-Fi MultiMedia (WMM) User Priority {{bibref|AMB}} that the throughput test is to run on. A value of 8 indicates that the WMM UP is not specified. If WMM is not supported by the BSS and the STA, then this is ignored. Duration of the throughput test in {{units}}. Direction to run the throughput test. {{enum}} Both uplink and downlink. Indicates the type of outcome of the throughput test request. {{enum}} This command represents a request to initiate a latency (delay) test set from a BSS to a STA. Each latency test set includes a number of individual echo tests. Each echo test result provides a sample of round-trip time. MAC address of the STA that the latency test is to be run to. The VLAN ID (VID) that the latency test is to run on. Wi-Fi MultiMedia (WMM) User Priority {{bibref|AMB}} that the latency test is to run on. A value of 8 indicates that the WMM UP is not specified. If WMM is not supported by the BSS and the STA, then this is ignored. Number of echo tests to run in the latency test set. If the value of this field is 0, then this field is ignored. If any echo test duration exceeds this time in {{units}}, then the echo test is declared a failure. A value of 0 indicates that no Timeout is specified. The size of each data block, in {{units}}, transmitted in each echo test. A value of 0 indicates that no DataBlockSize is specified. Indicates the type of outcome of the latency test request. {{enum}} Initiates a Wi-Fi Protected Setup (WPS) Push Button Configuration (PBC) process as defined in {{bibref|WPS 2.0}} . Indicates the response to the request to start Wi-Fi Protected Setup (WPS) Push Button Configuration (PBC). {{enum}} This parameter represents a request to initiate a channel scan on this radio on the given channel using a specific {{param|DwellTime}}. This command should result in updating {{object|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.ScanResult.}} If the instance of this {{object}} is the same as {{object|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}}}, then this command is similar to, {{command|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.ChannelScanRequest()}}. Indicates the type of outcome of the request to initiate a channel scan. {{enum}} This command defines access to other WiFi SSIDs that this device is able to receive. Indicates the availability of diagnostics data. {{enum}} If the value of this parameter is anything other than {{enum|Complete}}, the values of the other results parameters for this test are indeterminate. This command represents a request to reset or reboot the Wi-Fi sub-system without resetting or rebooting the device. This command requests the Wi-Fi backhaul link to be steered to associate to a different BSS when the device is working as a bridge in a mesh network. The device needs to already have the necessary credentials for the switch to happen. The {{param|TargetBSS}} should be an instance of a Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.BSSID. Indicates the response to the Wi-Fi backhaul steering request. {{enum}} This command represents a request to disassociate this associated device. Indicates the response to the request to disassociate an associated device. {{enum}} This command requests initiation of a BSS Transition Management (BTM) request to influence this client's roaming behavior to another BSS as defined in {{bibref|802.11-2020|Section 9.6.13.9}}. Indicates the response to the BSS Transition Management (BTM) request. {{enum}} The event is generated when an Associated Device (STA) associates to a BSS. Describes the Wi-Fi 6 capabilities of the Associated Device (STA). The event is generated when an Associated Device (STA) disassociates from a BSS. This object describes the final per link stats of each affiliated STA on disassociation. Applies only to Multi-Link Device (MLD) links. EasyMesh {{bibref|EasyMesh}} source: Affiliated STA Traffic Stats. The event is generated when an Associated Device (STA) fails to connect to a BSS. This command requests initiation of a Remote Measurement request to retrieve measurement data from a BSS on this radio. Upon receipt of this request, this radio is to initiate a measurement of the output {{param|SignalStrength}} and {{param|Noise}} for the indicated input. Indicates the response to the Remote Measurement request. {{enum}} This command represents a request to initiate a Clear Channel Assessment (CCA) measurement scan on this radio on the given channel using a specific {{param|DwellTime}}. Indicates the response to the request to initiate a Clear Channel Assessment (CCA) measurement. {{enum}} Initiates a Wi-Fi Protected Setup (WPS) Push Button Configuration (PBC) process as defined in {{bibref|WPS 2.0}} . Indicates the response to the request to start Wi-Fi Protected Setup (WPS) Push Button Configuration (PBC). {{enum}} Reset this {{object|#}} instance's WiFi security settings to their factory default values. The affected settings include {{param|ModeEnabled}}, {{param|WEPKey}}, {{param|PreSharedKey}}, {{param|KeyPassphrase}}, {{param|SAEPassphrase}}, and {{param|#.WPS.PIN}} (if applicable). If the command cannot be executed, the agent MUST reject the command. Possible failure reasons include a lack of default values or if {{param|ModeEnabled}} is an Enterprise type, i.e. {{enum|WPA-Enterprise|ModesSupported}}, {{enum|WPA2-Enterprise|ModesSupported}}, {{enum|WPA3-Enterprise|ModesSupported}}, or {{enum|WPA-WPA2-Enterprise|ModesSupported}}.