# The PSM breakpoint sub-carrier index in the range [0:4095], and
# the value of the level of the PSM at this sub-carrier expressed in
''0.1 dBm/Hz'' with an offset of -140 dBm/Hz.
Both values are represented as unsignedInt.
{{bibref|G.9964|Clause 5.2}} defines limits on PSM breakpoint levels.
The interface over which the test is to be performed.
The MAC address of the originating G.hn interface of the link that is
being diagnosed.
Note: This MAC address might belong to another node of the domain.
PHY throughput diagnostics results.
MAC address of the destination node of the link being measured.
Indicates the state of the link between the G.hn Interface with MAC
address {{param|#.DiagnoseMACAddress}} and the G.hn Interface with
MAC address {{param|DestinationMACAddress}}.
There is a direct link between G.hn Interface with MAC address
{{param|#.DiagnoseMACAddress}} and G.hn Interface with MAC
address {{param|DestinationMACAddress}}
There is no direct link between G.hn Interface with MAC address
{{param|#.DiagnoseMACAddress}} and G.hn Interface with MAC
address {{param|DestinationMACAddress}}
PHY data rate in transmit direction in the link between the G.hn
Interface with MAC address {{param|#.DiagnoseMACAddress}} and the
G.hn Interface with MAC address {{param|DestinationMACAddress}}. It
is represented in {{units}} as defined in Note 1 to
{{bibref|G.9961|Table 8-48}}. To convert from the value in the table,
divide by 32K (32768) and round down.
PHY data rate in receive direction in the link between the G.hn
Interface with MAC address {{param|#.DiagnoseMACAddress}} and the
G.hn Interface with MAC address {{param|DestinationMACAddress}}. It
is represented in {{units}} as defined in Note 1 to
{{bibref|G.9961|Table 8-48}}. To convert from the value in the table,
divide by 32K (32768) and round down.
The interface over which the test is to be performed.
The MAC address of the originating G.hn interface of the link that is
being diagnosed.
Note: This MAC address might belong to another node of the domain.
Time in {{units}} between automatic collection of performance
monitoring data. A value of zero disables automatic collection of data.
The node MAY impose a minimum sample interval, in which case an attempt
to set a (non-zero) interval that is less than this minimum MUST set
the interval to the minimum and MUST NOT be regarded as an error.
If SampleInterval is a simple fraction of a day, e.g. 900 (a quarter of
an hour) or 3600 (an hour), the device MAY choose to align sample
intervals with time of day, but is not required to do so.
The number of sub-carriers in a group to be used for averaging SNR
values when providing SNR information for a channel.
{{numentries}} This is the number of G.hn nodes for which performance
monitoring results were collected during the current sample interval.
{{numentries}}
Per-node G.hn performance monitoring results.
When automatic collection is enabled, i.e. {{param|#.SampleInterval}}
is non-zero, the "current" interval is defined by the most recent
automatic sample and the most recent subsequent manual sample, if any.
When automatic collection is disabled, i.e. SampleInterval is zero, the
"current" interval is defined by the three most recent manual samples.
Note: Packets in statistics counters are Ethernet packets.
Start time for the current interval.
When automatic collection is enabled, i.e. SampleInterval is
non-zero, the current interval started at the most recent automatic
sample.
When automatic collection is disabled, i.e. SampleInterval is zero,
the current interval started two manual samples ago.
End time for the current interval.
When automatic collection is enabled, i.e. SampleInterval is
non-zero, the current interval ended at the most recent manual sample
since the most recent automatic sample. If there has been no such
manual sample, the current interval is empty.
When automatic collection is disabled, i.e. SampleInterval is zero,
the current interval ended at the most recent manual sample.
Per-node G.hn performance monitoring results during the current sample
interval. Each table entry contains the results collected between the
G.hn nodes with MAC addresses {{param|##.DiagnoseMACAddress}}) and
{{param|DestinationMACAddress}}).
Note: Packet counters indicate the number of packets received between
{{param|#.CurrentStart}} and {{param|#.CurrentEnd}}.
MAC address of the destination node of the link being measured.
The total number of MPDU bytes transmitted or retransmitted by the
node through a physical medium (i.e., PMI defined in
{{bibref|G.9960|Clause 5.2.1}}), which correspond to data LPDUs
(i.e., data packets) and framing overhead (e.g., LFH, LPH, LPCS
defined in {{bibref|G.9961|Clause 8.1}}). It does not include
transmitted bytes contributed by management LPDUs (i.e., management
packets).
Note: LPDUs in mixed LLC frame blocks are considered data LPDUs.
The total number of MPDU bytes received by the node through a
physical medium, which correspond to data LPDUs and framing overhead.
It does not include received bytes contributed by management LPDUs.
It might include blocks with errors.
Note: LPDUs in mixed LLC frame blocks are considered data LPDUs.
The total number of APDUs requested for transmission by a higher
layer (i.e., outbound APDUs at the x1 reference point defined in
{{bibref|G.9960|Clause 5.2.1}}) that were transmitted by the node
through the physical medium. It does not include transmitted LCDUs.
The total number of APDUs delivered to a higher layer (i.e., inbound
APDUs at the x1 reference point) that were received by the node
through the physical medium. It does not include received LCDUs.
The total number of APDUs that were requested for transmission by a
higher layer (i.e., outbound APDUs at the x1 reference point defined
in {{bibref|G.9960|Clause 5.2.1}}). This parameter represents the
total number of LCDUs requested for transmission by a management
layer (i.e., outbound LCDUs generated in LLC defined in in
{{bibref|G.9961|Clause 8.1.3}}) that were transmitted by the node
through a physical medium) but could not be transmitted because of
errors (e.g., APDUs containing CRC errors).
The total number of received APDUs that contained errors preventing
them from being delivered to a higher layer (i.e., inbound APDUs at
the x1 reference point defined in {{bibref|G.9960|Clause 5.2.1}}).
The possible causes of error are: incorrect CRC, incorrect MIC,
incorrect MIC size, and incorrect size of packet.
The total number of APDUs that were requested for transmission by a
higher layer (i.e., outbound APDUs at the x1 reference point) and
which were addressed to a unicast address at this layer. It includes
APDUs that were discarded or not sent.
The total number of received APDUs that were delivered to a higher
layer (i.e., inbound APDUs at the x1 reference point) and which were
addressed to a unicast address at this layer.
The total number of APDUs that were requested for transmission by a
higher layer (i.e., outbound APDUs at the x1 reference point) but
chosen to be discarded even though no errors had been detected to
prevent their being transmitted (e.g., buffer overflow).
The total number of received APDUs that were chosen to be discarded
even though no errors had been detected to prevent their being
delivered.
The total number of APDUs that were requested for transmission by a
higher layer (i.e., outbound APDUs at the x1 reference point) and
which were addressed to a multicast address at this layer. It
includes APDUs that were discarded or not sent.
The total number of received APDUs that were delivered to a higher
layer (i.e., inbound APDUs at the x1 reference point) and which were
addressed to a multicast address at this layer.
The total number of APDUs that were requested for transmission by a
higher layer (i.e., outbound APDUs at the x1 reference point) and
which were addressed to a broadcast address at this layer. It
includes APDUs that were discarded or not sent.
The total number of received APDUs that were delivered to a higher
layer (i.e., inbound APDUs at the x1 reference point) and which were
addressed to a broadcast address at this layer.
The total number of APDUs received by the management that were
discarded because of an unknown or unsupported protocol.
The total number of MPDU bytes transmitted by the node through a
physical medium, which correspond to management LPDUs and framing
overhead.
The total number of MPDU bytes received by the node through a
physical medium, which correspond to management LPDUs and framing
overhead.
The total number of LCDUs requested for transmission by a management
layer (i.e., outbound LCDUs generated in LLC defined in
{{bibref|G.9961|Clause 8.1.3}}) that were transmitted by the node
through a physical medium.
The total number of LCDUs delivered to a management layer (i.e.,
inbound LCDUs) that were received by the node through a physical
medium.
The total number of LPDUs that were transmitted by the node through a
physical medium, regardless of new or retransmitted LPDUs.
The total number of LPDUs that were received by the node through a
physical medium, with or without errors.
The total number of LPDUs that were retransmitted.
The total number of received LPDUs that contained errors.
Note the following relationships hold:
* PacketsSent + ErrorsSent + DiscardPacketsSent = UnicastPacketsSent
+ MulticastPacketsSent + BroadcastPacketsSent.
* PacketsReceived = UnicastPacketsReceived + MulticastPacketsReceived
+ BroadcastPacketsReceived.
* Retransmission rate = BlocksResent / BlocksSent.
* Block error rate = BlocksErrorReceived / BlocksReceived.
Per-channel G.hn performance monitoring results.
Note: channels are unidirectional.
Time at which channel data was last collected.
Per-channel G.hn performance monitoring results during the current
sample interval. Each table entry contains the results collected from
the channel between a G.hn interface (as indicated by
{{param|##.DiagnoseMACAddress}}) and a G.hn interface indicated by
{{param|DestinationMACAddress}})
MAC address of the destination node of the link being measured.
The result of an SNR test performed over the channel. It is formatted
as a comma-separated list of N/M unsigned integers that represents
the result of Signal-to-Noise-Ratio measurement (in {{units}})
averaging in groups of M subcarriers. The number N depends on the
bandplan used by the node and corresponds to the OFDM control
parameter N of each medium as defined in {{bibref|G.9964}}. The
number M corresponds to the parameter {{param|##.SNRGroupLength}}.
G.hn object that contains an {{object|Interface}} table for G.hn
supported CPE. The ITU-T G.hn specifications {{bibref|G.9960}} and
{{bibref|G.9961}} define Physical and MAC Layers for communication
between two or more G.hn nodes in the home network over multiple wired
media such as power line, phone line and coaxial cable.
{{numentries}}
G.hn interface table (a stackable interface object as described in
{{bibref|TR-181i2|Section 4.2}}). Each table entry models the PHY
{{bibref|G.9960}} and MAC {{bibref|G.9961}} layers of a G.hn interface.
Enables or disables the interface.
This parameter is based on ''ifAdminStatus'' from {{bibref|RFC2863}}.
The current operational state of the interface (see
{{bibref|TR-181i2|Section 4.2.2}}). {{enum}}
When {{param|Enable}} is {{false}} then {{param}} SHOULD normally be
{{enum|Down}} (or {{enum|NotPresent}} or {{enum|Error}} if there is a
fault condition on the interface).
When {{param|Enable}} is changed to {{true}} then {{param}} SHOULD
change to {{enum|Up}} if and only if the interface is able to
transmit and receive network traffic; it SHOULD change to
{{enum|Dormant}} if and only if the interface is operable but is
waiting for external actions before it can transmit and receive
network traffic (and subsequently change to {{enum|Up}} if still
operable when the expected actions have completed); it SHOULD change
to {{enum|LowerLayerDown}} if and only if the interface is prevented
from entering the {{enum|Up}} state because one or more of the
interfaces beneath it is down; it SHOULD remain in the {{enum|Error}}
state if there is an error or other fault condition detected on the
interface; it SHOULD remain in the {{enum|NotPresent}} state if the
interface has missing (typically hardware) components; it SHOULD
change to {{enum|Unknown}} if the state of the interface can not be
determined for some reason.
This parameter is based on ''ifOperStatus'' from {{bibref|RFC2863}}.
The textual name of the interface as assigned by the CPE.
The accumulated time in {{units}} since the interface entered its
current operational state.
{{list}} {{reference|an interface object that is stacked immediately
below this interface object}} See {{bibref|TR-181i2|Section 4.2.1}}.
Note: Since {{object}} is a layer 1 interface, it is expected that
{{param}} will not be used.
Indicates whether the interface points towards the Internet
({{true}}) or towards End Devices ({{false}}).
For example:
* For an Internet Gateway Device, {{param}} will be {{true}} for all
WAN interfaces and {{false}} for all LAN interfaces.
* For a standalone WiFi Access Point that is connected via Ethernet
to an Internet Gateway Device, {{param}} will be {{true}} for the
Ethernet interface and {{false}} for the WiFi Radio interface.
* For an End Device, {{param}} will be {{true}} for all interfaces.
The MAC Address of the interface, denoted as node MAC address or
REGID in {{bibref|G.9961}}.
Note: This is not necessarily the same as the Ethernet header source
or destination MAC address, which is associated with the IP interface
and is modeled via the {{param|##.Ethernet.Link.{i}.MACAddress}}
parameter.
The firmware version of the interface.
{{deprecated|2.8|because it has been replaced by
{{param|MediumType}}}}
{{obsoleted|2.14}}
{{deleted|2.15}}
The maximum PHY data rate that the interface is capable of
transmitting (expressed in {{units}}).
{{list}} Identifies the target domains configured by the user, as
described in {{bibref|G.9961|Section 8.6.1}}. When registering or
re-registering, the G.hn interface SHOULD try to register to one of
these domains in the given order.
This is the domain name to which the interface is currently
registered.
{{empty}} indicates that the interface is currently not registered.
The Domain Name Identifier, a shortened version of
{{param|DomainName}}, denoted as DNI in {{bibref|G.9961|Section
8.6.11.2.1}}.
The Domain Identifier of the domain to which the interface is
registered, denoted as DOD in {{bibref|G.9961}}.
The Device Identifier assigned by the Domain Master, denoted as
DEVICE_ID in {{bibref|G.9961}}.
The value 0 indicates that the device is not currently registered.
The maximum PHY bit rate supported by this interface (expressed in
{{units}}).
Indicates whether this interface has the capability to act as Domain
Master in the G.hn domain.
Indicates a request to force the role of the G.hn interface to Domain
Master (DM) for the G.hn domain it is connected to. The selection of
the Domain Master follows the procedures described in
{{bibref|G.9961|Clause 8.6.6}}.
Indicates whether this G.hn interface is currently the Domain Master
(DM) for the G.hn domain it is connected to, as described in
{{bibref|G.9961|Clause 8.6}}.
Indicates whether this interface has the capability to act as
Security Controller in the G.hn domain.
Indicates a request to force the role of the G.hn interface to
Security Controller (SC) for the G.hn domain it is connected to. The
selection of the Security Controller follows the procedures described
in {{bibref|G.9961|Clause 9.2}}.
Indicates whether this G.hn interface is currently the Security
Controller (SC) for the G.hn domain it is connected to, as described
in {{bibref|G.9961|Clause 9.2}}.
The standard versions that the interface supports. The list MUST have
an even number of items. The first item of each pair represents an
ITU-T G.hn Recommendation while the second element of each pair
represents the amendment version of the indicated Recommendation that
this interface supports (the value 0 corresponds to the base
Recommendation).
For example, to indicate support for the G.9960 base document and
G.9961 amendment 1, the corresponding list would be
"G9960,0,G9961,1".
The largest bandplan that the interface can support, as defined in
{{bibref|G.9961|Clause 8.8.5.5}}.
The medium type that the interface currently operates on. Refer to
{{bibref|G.9962|Table 7-5}}.
The Acknowledgement InterFrame Gap, or TAIFG, as defined in
{{bibref|G.9961|Clause 8.4}}. It is represented as multiples of
{{units}}.
A bit map representing usage of international amateur bands (0 =
masked, 1 = unmasked). The LSB represents the lowest band (1.8-2.0
MHz), the second LSB represents the second lowest band (3.5-4.0 MHz),
and so on. The maximum value for this parameter is 0x03FF, i.e. it is
a 10-bit quantity represented in 16 bits and the top 6 bits are
always zero.
International Radio amateur bands are described in
{{bibref|G.9964|Table D-1}} and conveyed by the Domain Master in the
Amateur radio band descriptor (see {{bibref|G.9961|Table 8-77}}).
{{nolist}}
Comma-separated list of DeviceIDs of nodes that need to enable their
PHY throughput diagnostics mode. All devices that are enabled will
participate in the G.hn network PHY throughput diagnostics process.
{{nolist}}
Comma-separated list of DeviceIDs of nodes that need to enable their
Performance Monitoring diagnostics mode on this node. All devices
that are enabled will participate in the G.hn network Performance
Monitoring diagnostics process.
{{numentries}}
Requests the interface to become the Domain Master in the G.hn
domain.
This parameter is valid only if {{param|NodeTypeDMCapable}} is
{{true}}.
Note that, if more than one node is configured to act as Domain
Master, G.hn specifies a protocol to ensure only one device actually
becomes DM.
Indicates whether the interface is acting as Domain Master ({{true}})
or not ({{false}}).
See Note in {{param|NodeTypeDMConfig}} regarding the possibility of
more than one node being configured with {{param|NodeTypeDMConfig}} =
{{true}}.
Indicates whether the interface is acting as Security Controller
({{true}}) or not ({{false}}).
{{numentries}}
Specifies the list of PSD shaping mask (PSM) breakpoints to be
applied to the G.hn interface.
{{list|with each list item consisting of the following}}
{{datatype|expand}}
The PSM level is 0.1*(the value of the level of the PSM) - 140
dBm/Hz.
For example, a PSM defined by two breakpoints (subcarrier 450, PSM
level -80 dBm/Hz) and (subcarrier 1050, PSM level -90 dBm/Hz) is
represented by PSM [450,600],[1050,500] .
Throughput statistics for this interface at the different G.hn
reference points described in {{bibref|G.9961|Clause 8.1}}.
The CPE MUST reset the interface's Stats parameters (unless otherwise
stated in individual object or parameter descriptions) either when the
interface becomes operationally down due to a previous administrative
down (i.e. the interface's {{param|#.Status}} parameter transitions to
a down state after the interface is disabled) or when the interface
becomes administratively up (i.e. the interface's {{param|#.Enable}}
parameter transitions from {{false}} to {{true}}). Administrative and
operational interface status is discussed in {{bibref|TR-181i2|section
4.2.2}}.
The total number of bytes transmitted out of the interface, including
framing characters.
More specifically, this is the total number of MPDU bytes transmitted
or retransmitted by the node through a physical medium (i.e., PMI
defined in {{bibref|G.9960|Clause 5.2.1}}), which correspond to data
LPDUs (i.e., data packets) and framing overhead (e.g., LFH, LPH, LPCS
defined in {{bibref|G.9961|Clause 8.1}}). It does not include
transmitted bytes contributed by management LPDUs (i.e., management
packets).
Note: LPDUs in mixed LLC frame blocks are considered data LPDUs.
The total number of bytes received on the interface, including
framing characters.
More specifically, this is the total number of MPDU bytes received by
the node through a physical medium, which correspond to data LPDUs
and framing overhead. It does not include received bytes contributed
by management LPDUs. It can include blocks with errors.
Note: LPDUs in mixed LLC frame blocks are considered data LPDUs.
The total number of packets transmitted out of the interface.
More specifically, this is the total number of APDUs requested for
transmission by a higher layer (i.e., outbound APDUs at the x1
reference point defined in {{bibref|G.9960|Clause 5.2.1}}) that were
transmitted by the node through the physical medium. It does not
include transmitted LCDUs.
The total number of packets received on the interface.
More specifically, this is the total number of APDUs delivered to a
higher layer (i.e., inbound APDUs at the x1 reference point) that
were received by the node through the physical medium. It does not
include received LCDUs.
The total number of outbound packets that could not be transmitted
because of errors.
More specifically, this is the total number of APDUs that were
requested for transmission by a higher layer (i.e., outbound APDUs at
the x1 reference point defined in {{bibref|G.9960|Clause 5.2.1}}) but
could not be transmitted because of errors (e.g., APDUs containing
CRC errors).
The total number of inbound packets that contained errors preventing
them from being delivered to a higher-layer protocol.
More specifically, this is the total number of received APDUs that
contained errors preventing them from being delivered to a higher
layer (i.e., inbound APDUs at the x1 reference point defined in
{{bibref|G.9960|Clause 5.2.1}}). The possible causes of error are:
incorrect CRC, incorrect MIC, incorrect MIC size, and incorrect size
of packet.
The total number of packets requested for transmission which were not
addressed to a multicast or broadcast address at this layer,
including those that were discarded or not sent.
More specifically, this is the total number of APDUs that were
requested for transmission by a higher layer (i.e., outbound APDUs at
the x1 reference point) and which were addressed to a unicast address
at this layer. It includes APDUs that were discarded or not sent.
The total number of received packets, delivered by this layer to a
higher layer, which were not addressed to a multicast or broadcast
address at this layer.
More specifically, this is the total number of received APDUs that
were delivered to a higher layer (i.e., inbound APDUs at the x1
reference point) and which were addressed to a unicast address at
this layer.
The total number of outbound packets which were chosen to be
discarded even though no errors had been detected to prevent their
being transmitted. One possible reason for discarding such a packet
could be to free up buffer space.
More specifically, this is the total number of APDUs that were
requested for transmission by a higher layer (i.e., outbound APDUs at
the x1 reference point) but chosen to be discarded even though no
errors had been detected to prevent their being transmitted (e.g.,
buffer overflow).
The total number of inbound packets which were chosen to be discarded
even though no errors had been detected to prevent their being
delivered. One possible reason for discarding such a packet could be
to free up buffer space.
More specifically, this is the total number of received APDUs that
were chosen to be discarded even though no errors had been detected
to prevent their being delivered.
The total number of packets that higher-level protocols requested for
transmission and which were addressed to a multicast address at this
layer, including those that were discarded or not sent.
More specifically, this is the total number of APDUs that were
requested for transmission by a higher layer (i.e., outbound APDUs at
the x1 reference point) and which were addressed to a multicast
address at this layer. It includes APDUs that were discarded or not
sent.
The total number of received packets, delivered by this layer to a
higher layer, which were addressed to a multicast address at this
layer.
More specifically, this is the total number of received APDUs that
were delivered to a higher layer (i.e., inbound APDUs at the x1
reference point) and which were addressed to a multicast address at
this layer.
The total number of packets that higher-level protocols requested for
transmission and which were addressed to a broadcast address at this
layer, including those that were discarded or not sent.
More specifically, this is the total number of APDUs that were
requested for transmission by a higher layer (i.e., outbound APDUs at
the x1 reference point) and which were addressed to a broadcast
address at this layer. It includes APDUs that were discarded or not
sent.
The total number of received packets, delivered by this layer to a
higher layer, which were addressed to a broadcast address at this
layer.
More specifically, this is the total number of received APDUs that
were delivered to a higher layer (i.e., inbound APDUs at the x1
reference point) and which were addressed to a broadcast address at
this layer.
The total number of packets received via the interface which were
discarded because of an unknown or unsupported protocol.
More specifically, this is the total number of APDUs received by the
management that were discarded because of an unknown or unsupported
protocol.
The total number of MPDU bytes transmitted by the node through a
physical medium, which correspond to management LPDUs and framing
overhead.
The total number of MPDU bytes received by the node through a
physical medium, which correspond to management LPDUs and framing
overhead.
The total number of LCDUs requested for transmission by a management
layer (i.e., outbound LCDUs generated in LLC defined in
{{bibref|G.9961|Clause 8.1.3}}) that were transmitted by the node
through a physical medium.
The total number of LCDUs delivered to a management layer (i.e.,
inbound LCDUs) that were received by the node through a physical
medium.
The total number of LPDUs that were transmitted by the node through a
physical medium, regardless of new or retransmitted LPDUs.
The total number of LPDUs that were received by the node through a
physical medium, with or without errors.
The total number of LPDUs that were retransmitted.
The total number of received LPDUs that contained errors.
Note the following relationships hold:
* PacketsSent + ErrorsSent + DiscardPacketsSent = UnicastPacketsSent
+ MulticastPacketsSent + BroadcastPacketsSent.
* PacketsReceived = UnicastPacketsReceived + MulticastPacketsReceived
+ BroadcastPacketsReceived.
* Retransmission rate = BlocksResent / BlocksSent.
* Block error rate = BlocksErrorReceived / BlocksReceived.
This table contains information about other G.hn devices connected to
this G.hn interface.
MAC address of remote G.hn device.
This is denoted as REGID in {{bibref|G.9961}}.
Device Id (as defined in G.hn) for the remote G.hn device, denoted as
DEVICE_ID in {{bibref|G.9961}}.
The PHY transmit Rate (expressed in {{units}}) to this remote device,
denoted as PHY data rate in {{bibref|G.9961}}.
Refer to Note 1 of {{bibref|G.9961|Table 8-48}}. To convert from the
value in the table, divide by 32K (32768) and round down.
The PHY receive Rate (expressed in {{units}}) from this remote
device, denoted as PHY data rate in {{bibref|G.9961}}.
Refer to Note 1 of {{bibref|G.9961|Table 8-48}}. To convert from the
value in the table, divide by 32K (32768) and round down.
Whether or not this device is currently present in the G.hn domain.
The ability to list inactive nodes is OPTIONAL. If the CPE includes
inactive nodes in this table, {{param}} MUST be set to {{false}} for
each inactive node. The length of time an inactive node remains
listed in this table is a local matter to the CPE.
If {{param}} is {{true}}, it indicates that the Status of the remote
device is 0, 1, or 2 (see {{bibref|G.9961|Table 7-3}}).
This object specifies management parameters pertaining to the domain
functionality (Domain Master function; see {{bibref|G.9961|Clause
8.6}}). The object exists only on G.hn interfaces that are currently
the Domain Master, i.e. for which parameter {{param|#.IsDM}} is
{{true}}.
This is the domain name to which the interface is currently
registered. {{empty}} indicates that the interface is currently not
registered.
The Domain Name Identifier, a shortened version of
{{param|DomainName}}, denoted as DNI in {{bibref|G.9961|Section
8.6.11.2.1}}.
The Domain Identifier of the domain to which the interface is
registered, denoted as DOD in {{bibref|G.9961}}.
The MAC cycle duration, as specified in {{bibref|G.9961|Clause 8.4}}.
It is represented as multiples of {{units}}. In the case of power
line, writing to this parameter has no effect and it reads back as 0,
which is a special value indicating that the MAC cycle is
synchronized with 2 AC cycles as defined in {{bibref|G.9961|Clause
8.6.3.1}}.
The DEVICE_ID of the Security Controller selected by the Domain
Master.
The REGID of the Security Controller selected by the Domain Master.
The time interval for periodic re-registration, as specified in
{{bibref|G.9961|Clause 8.8.5.8}}. It is represented as multiples of
{{units}}.
The time interval that a node sends out the periodic topology update
using TM_NodeTopologyChange.ind message, as specified in
{{bibref|G.9961|Clause 8.8.5.8.1}}. It is represented as multiples of
{{units}}. The special value 0 represents an infinite interval (i.e.,
no periodic topology update).
Indicates the value of the minimal bandplan capability for a node
that is allowed to register to the domain.
Indicates the value of the minimal bandplan capability for a node
that is allowed to register to the domain.
This object specifies management parameters pertaining to the Security
Controller functionality (Security Controller function; see
{{bibref|G.9961|Clause 9.2}}). The object exists only on G.hn
interfaces that are currently the Security Controller, i.e. for which
parameter {{param|#.IsSC}} is {{true}}.
The security modes that the Security Controller can support. Refer to
{{bibref|G.9961|Clause 9.2}}.
Node-to-Node
Network Membership Key
The security mode in which the Security Controller is operating.
The selected MIC size used in the domain.
Indicates whether the Security Controller is above the L1 reference
point. It is set to {{true}} if the Security Controller is above the
L1 reference point, and set to {{false}} otherwise.
Specifies the list of masked bands to be applied to the G.hn interface.
This information is conveyed by the Domain Master in the SM descriptor
as specified in {{bibref|G.9961|Table 8-77}}.
Instances of this object are expected to exist only on G.hn interfaces
that are currently the Domain Master, i.e. for which parameter
{{param|#.IsDM}} is {{true}}.
Enables or disables the {{object}}.
The masked band number.
Index of the lowest frequency sub-carrier in the band to be masked as
specified in {{bibref|G.9961|Table 8-79}}. This parameter is writable
only on the interface which acts as the Domain Master.
Index of the highest frequency sub-carrier in the band to be masked
as specified in Table 8-79 in {{bibref|G.9961}}. This parameter is
writable only on the interface which acts as the Domain Master.
The G.hn Diagnostics object.