The direction of the traffic flow from the perspective of the AP MLD.
{{enum}}
The traffic identifier (TID) for this mapping.
The BSSID of the preferred link (affiliated AP) to use for traffic
with matching direction and TID values.
{{list}} The Link ID of the preferred link (affiliated AP) to use for
traffic with matching direction and TID values.
Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation
is enabled.
Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation
is enabled.
Indicates if Simultaneous Transmit and Receive (STR) operation
is enabled.
Indicates if Non-Simultaneous Transmit and Receive (NSTR)
operation is enabled.
Indicates if Traffic Identifier (TID) to Link Mapping Negotiation
is enabled.
{{bibref|EasyMesh}} source: TID-to-Link Mapping Policy TLV.
Table of Multi-Link Operation (MLO) capable Access Points (APs)
on this EasyMesh Agent or Single AP device.
{{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV.
The Multi-Link Device (MLD) MAC Address of the MLO Capable
access point (AP).
{{bibref|EasyMesh}} Source: Agent AP MLD Configuration TLV.
{{param}} is a reference to the APMLDTemplate selected for this
{{object}}.
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
This object describes the Wi-Fi 7 Multi-Link Operation (MLO)
configuration of the Multi-Link Device (MLD) Access Point (AP),
{{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV.
{{numentries}}
Table of Traffic Identifier (TID) to Operating Class to be used as a
policy when configuring TID-to-Link Mapping in the Multi-Link
Operation (MLO) capable access point (AP). Each table entry describes
the mapping between a particular TID and direction and the required
current Operating Class for any link to be used for this TID when
constructing a TID-to-Link Map {{bibref|EasyMesh|Section 20.2.8}}.
This parameter indicates whether the TID-to-Link mapping entry is enabled for Multi-Link Operation (MLO) on the access point (AP). When set to "true", the mapping between the specified Traffic Identifier (TID), direction, and required Operating Class will be active, and the TID-to-Link mapping policy will be applied during Multi-Link operations. When set to "false", the entry will be ignored.
The traffic identifier (TID) for this mapping.
This {{param}} is a unique key for this table.
{{list}} The Operating class of an available channel, from
{{bibref|802.11ax|Table E-4}}. The TID can be mapped to any link
using a radio with a current operating class within this list.
The direction of the traffic flow from the perspective the AP MLD.
{{enum}}
This {{param}} is a unique key for this table.
Table of Traffic Identifier (TID) to Link Mappings of the
Multi-Link Operation (MLO) capable access point (AP).
Each table entry describes the mapping between a
particular TID and direction and preferred link.
{{bibref|EasyMesh}} source: TID-to-Link Mapping Policy TLV.
This object describes the relationship between an Affiliated AP and
the Operating Class (OpClass) of the Radio that the Affiliated AP is
operating on {{bibref|EasyMesh|Section 20.2.8}}.
The Link ID assigned to one of the affiliated APs of this AP MLD.
{{bibref|EasyMesh|Section 17.2.96, Agent AP MLD Configuration TLV}}
One of the current Operating Class per {{bibref|802.11ax|Table E-4}}
that the Radio on which the Affiliated AP with the given
{{param|LinkID}} is operating on.
The Access Points (APs) affiliated to the AP MLD.
{{bibref|EasyMesh}} Source: Agent AP MLD Configuration TLV.
Counters in this object only include MLD traffic.
The BSSID of the affiliated AP. This should be set to one of the
values of {{param|##.Radio.{i}.BSS.{i}.BSSID}}.
{{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV.
The Link ID assigned to this affiliated AP.
{{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV.
The Radio unique identifier (RUID) of the Radio that this
affiliated AP is operating on.
{{bibref|EasyMesh}} source: Agent AP MLD Configuration TLV.
Disabled Subchannel Bitmap subfield from the EHT Operation element
in transmitted Management frames. Null value or not present for
stations.
{{bibref|EasyMesh}} source: Static Puncturing Configuration TLV.
The number of packets transmitted by the Affiliated AP. Note:
this counter counts only MLD traffic through this BSSID, not legacy
(non-MLD) traffic.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The total number of packets received from the affiliated STAs
by this Affiliated AP.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
Total number of unicast bytes transmitted to affiliated STAs associated
with this affiliated AP.
{{bibref|EasyMesh}} source: Affiliated AP Metrics TLV.
Total number of unicast bytes received from affiliated STAs associated
with this affiliated AP.
{{bibref|EasyMesh}} source: Affiliated AP Metrics TLV.
The number of packets which could not be transmitted by the
Affiliated AP due to errors.
This counter counts only MLD traffic through this BSSID,
not legacy (non-MLD) traffic.
{{bibref|EasyMesh}} source: Affiliated AP Metrics TLV.
Total multicast bytes transmitted to affiliated STAs associated with
this affiliated AP.
{{bibref|EasyMesh}} source: Affiliated AP Metrics TLV.
Total multicast bytes received from affiliated STAs associated with
this affiliated AP.
{{bibref|EasyMesh}} source: Affiliated AP Metrics TLV.
Total broadcast bytes transmitted to affiliated STAs associated with
this affiliated AP.
{{bibref|EasyMesh}} source: Affiliated AP Metrics TLV.
Total broadcast bytes received from affiliated STAs associated with
this affiliated AP.
{{bibref|EasyMesh}} source: Affiliated AP Metrics TLV.
Estimated Service Parameters information field for AC=BE, defined
per {{bibref|802.11-2020|Figure 9-637}} and referenced in
{{bibref|EasyMesh|Section 17.2.22}}.
Estimated Service Parameters information field for AC=BK, defined
per {{bibref|802.11-2020|Figure 9-637}} and referenced in
{{bibref|EasyMesh|Section 17.2.22}}.
Estimated Service Parameters information field for AC=VI, defined
per {{bibref|802.11-2020|Figure 9-637}} and referenced in
{{bibref|EasyMesh|Section 17.2.22}}.
Estimated Service Parameters information field for AC=VO, defined
per {{bibref|802.11-2020|Figure 9-637}} and referenced in
{{bibref|EasyMesh|Section 17.2.22}}.
This object describes Multi-Link Operation (MLO) capable stations
(STAs), also known as client Multilink Devices (MLDs), associated to
this MLO capable Access Point.
{{bibref|EasyMesh}} source: Associated Clients TLV.
The Multi-Link Device (MLD) MAC Address of the STA MLD.
{{bibref|EasyMesh}} source: Associated STA MLD Configuration Report
TLV.
The Hostname for the STA MLD.
The IPv4 address allocated to the MLD MAC Address of this device.
The IPv6 address allocated to the MLD MAC Address of this device.
Indicates if the STA MLD is a backhaul STA MLD (bSTA MLD).
This is useful to identify the type of STA MLD when the same
AP MLD is used for both Fronthaul and Backhaul operation.
{{bibref|EasyMesh}} source: Backhaul STA MLD Configuration TLV.
The time in {{units}} since this STA MLD was associated.
The total number of bytes transmitted to the STA MLD.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The total number of bytes received from the STA MLD.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The total number of packets transmitted to the STA MLD.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The total number of packets received from the STA MLD.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The number of packets which could not be transmitted to the
STA MLD due to errors.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The number of packets which were received with error from the
STA MLD.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The number of packets transmitted with the retry flag sent to
the STA MLD.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
Pairwise AKM suite selector selected by the STA MLD.
The Pairwise AKM suite selector (OUI and type) is encoded as a 4-octet
hex-encoded value without internal delimiters, e.g. 506F9A02
{{bibref|802.11-2020|Table 9-151}}.
Pairwise AKM cipher selector selected by the STA MLD.
The Pairwise AKM cipher selector (OUI and type) is encoded as a 4-octet
hex-encoded value without internal delimiters, e.g. 506F9A02
{{bibref|802.11-2020|Table 9-149}}.
The RSN Capabilities selected by the STA MLD during association
{{bibref|802.11-2020|Section 9.4.2.24.4}}.
{{numentries}}
{{numentries}}
This object describes the Wi-Fi 7 capabilities for this STA MLD
including Multi-Link Operation (MLO) capabilities.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation
is supported by this STA MLD.
Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation
is supported by this STA MLD.
Indicates if Simultaneous Transmit and Receive (STR) operation
is supported by this STA MLD.
Indicates if Non-Simultaneous Transmit and Receive (NSTR)
operation is supported by this STA MLD.
Indicates if Traffic Identifier (TID) to Link Mapping Negotiation
is supported by this STA MLD.
This object describes the Wi-Fi 7 Multi-Link Operation (MLO)
configuration of the Multi-Link Device (MLD)
station (STA, also called associated device).
Note this may differ from the WiFi7 capabilities of the device.
{{bibref|EasyMesh}} source: Associated STA MLD Configuration Report
TLV.
Indicates if the Enhanced Multi-Link Multi-Radio (EMLMR) operation
is enabled.
Indicates if Enhanced Multi-Link Single-Radio (EMLSR) operation
is enabled.
Indicates if Simultaneous Transmit and Receive (STR) operation
is enabled.
Indicates if Non-Simultaneous Transmit and Receive (NSTR)
operation is enabled.
Indicates if Traffic Identifier (TID) to Link Mapping Negotiation
is enabled.
{{bibref|EasyMesh}} source: TID-to-Link Mapping Policy TLV.
Table of Traffic Identifier (TID) to Link Mappings of the
Multi-Link Operation (MLO) capable station (STA).
Each table entry describes the mapping between a
particular TID and direction and preferred link.
{{bibref|EasyMesh}} source: TID-to-Link Mapping Policy TLV.
This object describes stations (STAs, also called associated devices)
that are affiliated to this Multi-Link Device (MLD) STA.
{{bibref|EasyMesh}} source: Associated STA MLD Configuration TLV.
The MAC address of the affiliated STA.
{{bibref|EasyMesh}} source: Associated STA MLD Configuration
Report TLV.
The BSSID of the affiliated AP that the affiliated STA is
associated to.
{{bibref|EasyMesh}} source: Associated STA MLD Configuration
Report TLV.
The total number of bytes transmitted to the affiliated STA.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The total number of bytes received from the affiliated STA.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The total number of packets transmitted to the affiliated STA.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The total number of packets received from the affiliated STA.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
The number of packets which could not be transmitted to the
affiliated STA due to errors.
{{bibref|EasyMesh}} source: Associated STA Traffic Stats TLV.
An indicator of radio signal strength of the uplink from the
affiliated STA to the access point - measured in {{units}}. RCPI is
encoded per {{bibref|802.11-2020|Table 9-176}}, and described in
{{bibref|EasyMesh|Section 10.3.1}}). Reserved: 221 - 255.
Estimate of the MAC layer throughput in {{units}} achievable in the
downlink direction if 100% of channel airtime and BSS operating
bandwidth were available, as defined in {{bibref|EasyMesh|Section
10.3.1}}.
Estimate of the MAC layer throughput in {{units}} achievable in the
uplink direction if 100% of channel airtime and BSS operating
bandwidth were available, as defined in {{bibref|EasyMesh|Section
10.3.1}}.
The data transmit rate in {{units}} that was most recently used for
transmission of data from the access point to the affiliated STA.
The data transmit rate in {{units}} that was most recently used for
transmission of data from the affiliated STA to the access point.
The amount of time in {{units}} that the AP MLD Radio has spent on
the channel receiving data from the affiliated STA.
The amount of time in {{units}} that the AP MLD Radio has spent on
the channel transmitting data to the affiliated STA.
This object represents the Multi-Link Operation (MLO) capable backhaul
station (bSTA) operating on this EasyMesh Agent. Only one MLO capable
bSTA per EasyMesh Agent is allowed.
{{bibref|EasyMesh}} source: Backhaul STA MLD Configuration TLV.
The Multi-Link Device (MLD) MAC Address of the MLO Capable bSTA.
{{bibref|EasyMesh}} Source: Backhaul STA MLD Configuration TLV.
The MLD MAC address of the upstream AP MLD that this bSTA MLD
is associated to.
{{bibref|EasyMesh}} source: Associated Clients TLV.
{{list}} backhaul STA MAC addresses affiliated to this bSTA MLD.
{{bibref|EasyMesh}} source: Backhaul STA MLD Configuration TLV.
This object describes the Multi-Link Operation (MLO) configuration of
a Multi-Link Device (MLD) backhaul STA (bSTA).
{{bibref|EasyMesh}} source: Backhaul STA MLD Configuration TLV.
Enable downlink (DL) Orthogonal Frequency-Division Multiple Access
(OFDMA).
Enable uplink (UL) OFDMA.
Enable DL Multi-User Multi-Input Multi-Output (MU-MIMO).
Enable UL MU-MIMO.
Total number of Physical-layer Protocol Data Units (PPDUs)
transmitted by the Wi-Fi Basic Service Set (BSS).
Number of High-Efficiency (HE) PPDUs transmitted by the BSS.
Number of Multi-User (MU) PPDUs transmitted by the BSS.
Number of Orthogonal Frequency-Division Multiple Access (OFDMA)
PPDUs transmitted by the BSS.
Number of Multi-Input Multi-Output (MU-MIMO) PPDUs
transmitted by the BSS.
Number of PPDUs transmitted by the BSS with OFDMA and
MU-MIMO.
Total number of PPDUs received by the BSS.
Number of High-Efficiency (HE) PPDUs received by the BSS.
Number of MU PPDUs received by the BSS.
Number of OFDMA PPDUs received by the BSS.
Number of MU-MIMO PDDUs received by the BSS.
Number of PPDUs received by the BSS with OFDMA and MU-MIMO.
Number of PPDUs sent on the downlink using Resource Unit (RU) RU26.
Number of PPDUs sent on the downlink using RU52.
Number of PPDUs sent on the downlink using RU106.
Number of PPDUs sent on the downlink using RU242.
Number of PPDUs sent on the downlink using RU484.
Number of PPDUs sent on the downlink using RU996.
Number of PPDUs sent on the downlink using RU1992.
Number of PPDUs received on the uplink using RU26.
Number of PPDUs received on the uplink using RU52.
Number of PPDUs received on the uplink using RU106.
Number of PPDUs received on the uplink using RU242.
Number of PPDUs received on the uplink using RU484.
Number of PPDUs received on the uplink using RU996.
Number of PPDUs received on the uplink using RU1992.
Indicates support for High Efficiency (HE) 160 MHz.
Indicates support for HE 80+80 MHz.
Supported High Efficiency-Modulation and Coding Scheme (HE-MCS) and
Number of Spatial Streams (NSS) Set field as defined in
{{bibref|802.11ax|Figure 9-788d}} Supported HE-MCS And NSS Set field
format. HE-MCS And NSS Set field for 160MHz is present if 160MHz is
supported. HE-MCS And NSS Set field for 80+80MHz is present if 80+80MHz
is supported.
Indicates support for Single-User (SU) Beamformer.
Indicates support for SU Beamformee.
Indicates support for Multi-User (MU) Beamformer.
Indicates support for Beamformee Space-Time Stream (STS) ≤ 80 MHz.
Indicates support for Beamformee STS > 80 MHz.
Indicates support for Uplink (UL) Multi-User Multiple Input, Multiple
Output (MU-MIMO).
Indicates support for UL Orthogonal Frequency Division Multiplexing
(OFDMA).
Indicates support for Downlink (DL) Orthogonal Frequency Division
Multiplexing (OFDMA).
Max number of users supported per DL MU-MIMO Transmitter (TX) in the BSS
role.
Max number of users supported per UL MU-MIMO Receiver (RX) in the BSS
role.
Max number of users supported per Downlink (DL) OFDMA TX in the BSS role.
Max number of users supported per UL OFDMA RX in the BSS role.
Indicates support for Request To Send (RTS).
Indicates support for MU RTS.
Indicates support for Multi-Basic Service Set Identifier (BSSID).
Indicates support for MU Enhanced distributed channel access (EDCA).
Indicates support for Target Wake Time (TWT) Requestor.
Indicates support for TWT Responder.
Indicates support for EasyMesh configuration and reporting of BSS Color
and Spatial Reuse.
Indicates support for Anticipated Channel Usage (ACU) reporting.
Any Organizationally Unique Identifier (OUI) value specified in
{{bibref|802.11-2020|Table 9-151}}).
Any suite type value specified in {{bibref|802.11-2020|Table 9-151}}.
The SSID.
The VLAN ID (VID).
Service prioritization rule Identifier.
Rule Precedence - higher number means higher priority.
Rule Output. The value of, or method used to select, the 802.1Q C-TAG
Priority Code Point (PCP) output value.
Indicates if the rule always matches.
The value of the BSS Color subfield of the
HEOperations.BSSColorInformation field being transmitted by BSSs
operating on this radio. (EasyMesh TLV Field: BSS Color)
Indicates if the Agent is allowed to set HESIGA.SpatialReuse field to
value 15 (PSR_AND_NON_SRG_OBSS_PD_PROHIBITED) in HE PPDU transmissions
of this radio. (EasyMesh TLV Field:
HESIGA_Spatial_reuse_value15_allowed)
: {{true}}: allowed;
: {{false}}: disallowed.
This field indicates whether the SRG Information fields (SRG OBSS PD
Min Offset, SRG OBSS PD Max Offset, SRG BSS Color Bitmap and SRG
Partial BSSID Bitmap) in this command are valid. (EasyMesh TLV Field:
SRG Information Valid)
: {{true}}: SRG Information fields valid;
: {{false}}: SRG Information fields not valid.
This field indicates whether the Non-SRG OBSSPD Max Offset field in
this command is valid. (EasyMesh TLV Field: Non-SRG Offset Valid)
: {{true}}: Non-SRG Max Offset field valid;
: {{false}}: Non-SRG Max Offset field not valid.
Indicates if the Agent is disallowed to use Parameterized Spatial Reuse
(PSR)-based Spatial Reuse for transmissions by the specified radio.
(EasyMesh TLV Field: PSR Disallowed)
: {{true}}: PSR disallowed;
: {{false}}: PSR allowed.
The value of dot11NonSRGAPOBSSPDMaxOffset (i.e the Non-SRG OBSSPD Max
Offset value being used to control the transmissions of the specified
radio). (EasyMesh TLV Field: Non-SRG OBSSPD Max Offset)
This field is valid only if {{param|NonSRGOffsetValid}} is {{true}}.
The value of dot11SRGAPOBSSPDMinOffset (i.e. the SRG OBSSPD Min Offset
value being used to control the transmissions of the specified radio).
(EasyMesh TLV Field: SRG OBSSPD Min Offset)
This field is valid only if {{param|SRGInformationValid}} is {{true}}.
The value of dot11SRGAPOBSSPDMaxOffset (i.e. the SRG OBSSPD Max Offset
value being used to control the transmissions of the specified radio).
(EasyMesh TLV Field: SRG OBSSPD Max Offset)
This field is valid only if {{param|SRGInformationValid}} is {{true}}.
The value of dot11SRGAPBSSColorBitmap (i.e. the SRG BSS Color Bitmap
being used to control the tranmissions of the specified radio).
(EasyMesh TLV Field: SRG BSS Color Bitmap)
This field is valid only if {{param|SRGInformationValid}} is {{true}}.
The value of dot11SRGAPBSSIDBitmap (i.e. the SRG Partial BSSID Color
Bitmap being used to control the transmissions of the specified radio).
(EasyMesh TLV Field: SRG Partial BSSID Bitmap)
This field is valid only if {{param|SRGInformationValid}} is {{true}}.
Note: See rules in section 26.10.2.3 of [17] regarding the members of
an SRG.
Indicates support for 4 MHz operation.
Indicates support for 8 MHz operation.
Indicates support for 16 MHz operation.
Indicates support for the reception of S1G_LONG Physical layer
Protocol Data Units (PPDUs).
Indicates support for 1 MHz short Guard Interval (GI).
Indicates support for 2 MHz short GI.
Indicates support for 4 MHz short GI.
Indicates support for 8 MHz short GI.
Indicates support for 16 MHz short GI.
Indicates support of Aggregated MAC Service Data Units (AMSDU).
Indicates support of Aggregated MAC Protocol Data Units (AMPDU).
Indicates support for Flow Control
{{bibref|802.11-2020|Section 10.61}}.
Indicates support for Centralized Authentication Control
{{bibref|802.11-2020|Section 11.3.9.2}}.
Indicates support for Distributed Authentication Control (DAC)
{{bibref|802.11-2020|Section 11.3.9.3}}.
Indicates the maximum MAC Protocol Data Unit (MPDU) length in octets.
{{enum}}
Indicates support of non-Traffic Indication Map (non-TIM) operation
{{bibref|802.11-2020|Section 10.48}}.
Indicates support of Dynamic Association ID (AID) operation
{{bibref|802.11-2020|Section 10.20}}.
Indicates support of Group Association ID (AID)
{{bibref|802.11-2020|Section 10.55}}.
Indicates support for the use of the Block Acknowledgment
TWT (BAT) frame in Block Agreements
{{bibref|802.11-2020|Section 9.8.4.3}}.
Indicates support for Restricted access window (RAW) operation
{{bibref|802.11-2020|Section 10.23.5}}.
Indicates support for Page Slicing Operation
{{bibref|802.11-2020|Section 10.51}}.
Indicates support for Protocol Version 1 (PV1) frames
{{bibref|802.11-2020|Section 9.8}}.
Supported Tx S1G-MCS Map subfield and Coding Scheme (S1G-MCS) and
Number of Spatial Streams (NSS) Set field as defined in
{{bibref|802.11-2020|Figure 9-694}}.
Supported Rx S1G-MCS Map subfield and Coding Scheme (S1G-MCS) and
Number of Spatial Streams (NSS) Set field as defined in
{{bibref|802.11-2020|Figure 9-694}}.
Indicates support for Single-User (SU) Beamformer
{{bibref|802.11-2020|10.36.5 VHT sounding protocol}}.
Indicates support for Single-User (SU) Beamformee
{{bibref|802.11-2020|10.36.5 VHT sounding protocol}}.
Indicates support for Multi-User (MU) Beamformer
{{bibref|802.11-2020|10.36.5 VHT sounding protocol}}.
Indicates support for Multi-User (MU) Beamformee
{{bibref|802.11-2020|10.36.5 VHT sounding protocol}}.
Indicates support for or the reception of PPDUs with traveling pilots
{{bibref|802.11-2020|10.56 Traveling pilot operation}}.
Indicates support for Target Wake Time (TWT) Grouping
{{bibref|802.11-2020|10.47.5 TWT grouping}}.
Indicates support for Target Wake Time (TWT) Requestor
{{bibref|802.11-2020|10.47 Target wake time (TWT)}}.
Indicates support for Target Wake Time (TWT) TWTResponder
{{bibref|802.11-2020|10.47 Target wake time (TWT)}}.
This object represents the Wi-Fi Alliance Data Elements as defined in
{{bibref|DataElements}} with extended capabilities in additional
objects whose names begin with MultiAP.
This object describes a Wi-Fi network containing 1 or more Access Point
(AP) devices.
A unique identifier for this particular Wi-Fi network.
The time this group was collected. Formatted with the date-and-time
string format as defined in {{bibref|RFC3339|Section 3}}.
A unique identifier for a Multi-AP controller.
It is recommended that this be the same as the
IEEE 1905 ALID of the EasyMesh controller.
{{numentries}}
List of STAs for which Mirrored Stream Classification Service (MSCS)
operation is disallowed.
List of STAs for which Stream Classification Service (SCS) operation
is disallowed.
AL MAC address of the EasyMesh Agent that is co-located in the
same device with the Wi-Fi EasyMesh Controller.
Set to null if there is no such collocated agent.
Count of number of EasyMesh controller-initiated requests for
Steering Mandates.
{{bibref|EasyMesh|Section 17.2.57, Profile-2 Steering Request TLV,
with field Request_Mode set to one}}.
Count of number of EasyMesh controller-initiated requests for
Steering Opportunities.
{{bibref|EasyMesh|Section 17.2.57, Profile-2 Steering Request TLV,
with field Request_Mode set to zero}}.
{{numentries}}
{{numentries}}
{{numentries}}
This object specifies SSIDs for fronthaul use across all agents in this
Wi-Fi Multi-AP network, or on this single-AP. Also specifies the
{{param|Band}} for each {{param|SSID}}.
The {{param|Alias}} can be used to uniquely refer to this table entry
corresponding to a BSS even if the {{param|SSID}} were to change.
Note that VLAN IDs (VIDs) can be configured per SSID with
{{object|#.Device.{i}.SSIDtoVIDMapping.{i}}}.
The SSID for fronthaul use across this Wi-Fi Multi-AP network.
The band(s) (GHz) for which this {{param|SSID}} applies. {{enum}}
Applies to all bands
2.4 GHz band
The entire 5 GHz band
The entire 6 GHz band
5 GHz UNII-1 band, 5.15 to 5.25 GHz
5 GHz UNII-2 band, 5.25 to 5.725 GHz
5 GHz UNII-3 band, 5.725 to 5.85 GHz
5 GHz UNII-4 band, 5.85 to 5.925 GHz
6 GHz UNII-5 band, 5.925 to 6.425 GHz
6 GHz UNII-6 band, 6.425 to 6.525 GHz
6 GHz UNII-7 band, 6.525 to 6.875 GHz
6 GHz UNII-8 band, 6.875 to 7.125 GHz
Sub 1 GHz band, 800 MHz to 928 MHz
Enable or disable of this {{param|SSID}}. Disable stops the use of
this {{param|SSID}}, but the object is retained.
: {{true}}: this {{param|SSID}} is enabled.
: {{false}}: this {{param|SSID}} is disabled.
{{list}} List items indicate Authentication and Key Management (AKM)
suites/security modes allowed on this BSS. {{enum}}
"psk" indicates one or more of the PSK and FT-PSK AKMs defined
in {{bibref|802.11-2020|Table 9-151}} typically at least
"00-0F-AC:2" for interoperability.
"dpp" indicates one or more of the DPP and FT-DPP AKMs defined
in {{bibref|EasyConnect|Section 8.4}}, typically at least
"50-6F-9A:2" for interoperability.
"sae" indicates one or more of the SAE and FT-SAE AKMs defined
in {{bibref|802.11-2020|Table 9-151}} typically at least
"00-0F-AC:8" for interoperability.
"SuiteSelector" indicates an AKM suite selector, the value of
which is indicated in {{param|SuiteSelector}}.
AKM suite selector, the AKM suite selector (OUI and type) is
encoded as a 4-octet hex-encoded value without internal
delimiters, e.g. 506F9A02 {{bibref|802.11-2020|Table 9-151}}.
This parameter applies if {{param|AKMsAllowed}} includes value
"SuiteSelector".
Indicates if the SSID is advertised in beacons, or not.
: {{true}}: this {{param|SSID}} is to be advertised in beacons.
: {{false}}: this {{param|SSID}} is not to be advertised in beacons.
Management Frame Protection (MFP) configuration. {{enum}}
The IEEE 802.11 mobility domain
{{bibref|802.11-2020|Section 9.4.2.46}}.
Indicates the use of this {{param|SSID}}. {{enum}}
Human-readable description for the BSS referenced by this
{{object}}. For example {{param}} could be one of Primary, Home,
Guest, Public, Private, Children, Video, Backhaul, Not Children,
or Public 2.
This object indicates stations (STAs) for which client association is
blocked.
optionally the BSSID(s) the STA is blocked from associating to.
In multi-AP cases, this should be implemented by Wi-Fi EasyMesh
{{bibref|EasyMesh}} client association control.
Stations that are already associated shall be disassociated if
{{object|#.STABlock.{i}.Schedule.{i}.}} indicates so.
MAC addresses of the STA that is blocked.
{{list}} Indicates BSS from which the {{param|BlockedSTA}}
is blocked from association and cannot associate to. A null list
indicates that all SSIDs are blocked.
{{numentries}}
Each instance of this object provides a schedule where
client association is blocked for {{param|#.BlockedSTA}}
{{bibref|EasyMesh|Section 11.6}}.
{{list|the days for which the STA is blocked}} {{enum}}
Start time of the STA block in hh:mm format.
[hh] refers to a zero-padded hour between 00 and 23.
[mm] refers to a zero-padded minute between 00 and 59.
Start time is in local time zone.
The duration, in {{units}}, which the STA is blocked.
If {{param|StartTime}} is defined, the STA is blocked for the
{{param}} period starting from {{param|StartTime}}.
This table contains provisioned Device Provisioning Protocol (DPP)
Boostrap URIs {{bibref|EasyConnect|Section 5.2.1}} which contain
bootstrapping keys available to the Multi-AP controller for trusted
third party onboarding of new Multi-AP agents.
The boostrapping DPP URI information which contains the enrollee
public key to use for DPP onboarding a Multi-AP agent as specified
by {{bibref|EasyConnect|Section 5.2.1}}.
The summary of statistics related to Multi-AP Steering for the Wi-Fi
network.
The counters contained in {{object}} are all reset on reboot.
Number of times Associated Devices should have been steered but
weren't because a better candidate AP couldn't be found.
Number of times a Blacklist steer was attempted.
Number of times an attempted Blacklist steer succeeded.
Number of times an attempted Blacklist steer failed.
Number of times a BTM (BSS Transition Management; {{bibref|802.11k}})
steer was attempted.
Number of times an attempted BTM (BSS Transition Management;
{{bibref|802.11k}}) steer succeeded.
Number of times an attempted BTM (BSS Transition Management;
{{bibref|802.11k}}) steer failed.
Number of asynchronous BTM (BSS Transition Management;
{{bibref|802.11k}}) Queries for which a BTM Request was issued.
Each instance of this object represents an individual EasyMesh Agent
or single-AP device in the Wi-Fi network.
A unique identifier for this particular device within the Wi-Fi
network as defined in {{bibref|DataElements|Section 3.1}}.
If this {{object}} is represented in
{{object|Device.IEEE1905.AL.NetworkTopology.}},
then this should match an IEEE 1905 AL MAC Address in
{{param|Device.IEEE1905.AL.NetworkTopology.IEEE1905Device.{i}.IEEE1905Id}}.
The Multi-AP capabilities supported by this device as defined by the
APCapability TLV in {{bibref|EasyMesh|Section 17.2.6}}.
The interval between the collection of consecutive measurements of
the most frequently updated Data Element from this device in
{{units}}.
Indicates whether the Multi-AP Agent or the single AP reports
unsuccessful association attempts of client Stations (STAs) to the
Multi-AP Controller.
Maximum rate for reporting unsuccessful association attempts in
{{units}}.
{{deprecated|2.19|because it was the same as
{{param|MaxUnsuccessfulAssociationReportingRate}}.}}
{{obsoleted|2.21}}
AP Metrics Reporting Interval.
: 0: Do not report AP Metrics periodically;
: 1 - 255: AP Metrics reporting interval in {{units}}.
Associated STA Reporting Interval.
0: Do not report associated STA Metrics periodically;
1 - 255: Associated STA Metrics reporting interval in {{units}}.
Identifier of the manufacturer of the device.
If the instance of this {{object}} is the same as {{object|Device.}},
then this parameter is the same as
{{param|Device.DeviceInfo.Manufacturer}}.
Identifier of the particular Access Point device that is unique for
the indicated model and manufacturer.
This value MUST remain fixed over the lifetime of the device,
including across firmware updates.
If the instance of this {{object}} is the same as {{object|Device.}},
then this parameter is the same as
{{param|Device.DeviceInfo.SerialNumber}}.
Identifier of the manufacturer model to help the user more easily
identify a particular piece of equipment.
If the instance of this {{object}} is the same as {{object|Device.}},
then this parameter is the same as
{{param|Device.DeviceInfo.ModelName}}.
Identifier of the software version currently installed in the Access
Point device (i.e. version of the overall firmware).
If the instance of this {{object}} is the same as {{object|Device.}},
then this parameter is the same as
{{param|Device.DeviceInfo.SoftwareVersion}}.
Identifier of the execution environment (operating system) in the
device. This parameter can be an entry in the table
{{object|####.SoftwareModules.ExecEnv}}.
If the instance of this {{object}} is the same as {{object|Device.}},
then this parameter is the same as
{{object|Device.SoftwareModules.ExecEnv.{i}.}}.
A hexadecimal string of 64 Priority Code Point (PCP) values (one
octet per value) corresponding to the Differentiated Services Code
Point (DSCP) markings 0x00 to 0x3F, ordered by increasing DSCP value.
Each octet is in the range 0x00 - 0x07. This is used to select a PCP
value if a Service Prioritization Rule specifies Rule Output: 0x08
The maximum total number of service prioritization rules supported by
the Agent.
Indicates support for Service Prioritization.
Max Total Number of unique VLAN IDs (VIDs) the Multi-AP Agent
supports.
Associated Wi-Fi6 STA Status Inclusion Policy.
: {{true}}: Include Associated Wi-Fi6 STA Status TLV in AP Metrics
Response.
: {{false}}: Do not include Associated Wi-Fi6 STA Status TLV [3] in
AP Metrics Response.
{{deprecated|2.16|because it was the same as
{{param|Radio.{i}.APMetricsWiFi6}}.}}
{{obsoleted|2.18}}
{{deleted|2.19}}
Two-character country code in which the Multi-AP Agent is operating
according to {{bibref|ISO3166-1}}. The characters are encoded as
UTF-8.
If the instance of this {{object|##}} is the same as
{{object|Device.WiFi.Radio.{i}.}}, then this parameter is the same
as the first two octets of
{{param|Device.WiFi.Radio.{i}.RegulatoryDomain}}.
{{list}} The STAs for which local steering is disallowed.
{{list}} The STAs for which BSS Transition Management (BTM) steering
is disallowed.
Indicates if Dynamic Frequency Selection (DFS) is enabled or
disabled.
Channel Scan Reporting Policy, Report Independent Channel Scans
: {{true}}: report Independent Channel Scans,
: {{false}}: do not report Independent Channel Scans unless
explicitly requested in a Channel Scan Request.
For EasyMesh {{bibref|EasyMesh}}, this is the Associated Wi-Fi6 STA
Status Inclusion Policy.
: {{true}}: Include Associated Wi-Fi6 STA Status TLV in AP Metrics
Response;
: {{false}}: Do not include Associated Wi-Fi6 STA Status TLV in AP
Metrics Response.
{{deprecated|2.16|because it was the same as
{{param|Radio.{i}.APMetricsWiFi6}}.}}
{{obsoleted|2.18}}
{{deleted|2.19}}
For EasyMesh {{bibref|EasyMesh}}, this is the maximum rate for
reporting unsuccessful association attempts (in attempts per
{{units}}).
Indicates if EasyMesh {{bibref|EasyMesh}} controller-initiated
station steering is disallowed or allowed on this device.
: {{true}}: EasyMesh controller-initiated station steering
disallowed;
: {{false}}: EasyMesh controller-initiated station steering allowed.
Allow or disallow the use of EasyMesh {{bibref|EasyMesh}} Coordinated
Channel Availability Check (CAC) on this device.
: {{true}}: allowed;
: {{false}}: disallowed.
This parameter indicates if EasyMesh traffic separation
{{bibref|EasyMesh|Section 19.1}} is allowed or disallowed.
This parameter indicates if EasyMesh service prioritization
{{bibref|EasyMesh|Section 20}} is allowed or disallowed.
This parameter represents the status of Wi-Fi EasyMesh controller
functionality. {{enum}}
Wi-Fi EasyMesh controller is not supported.
Wi-Fi EasyMesh controller is supported but not
enabled.
Wi-Fi EasyMesh controller is running.
The MAC address of the
interface on the network that is providing the backhaul for
this EasyMesh Agent. For Wi-Fi backhaul, this is the BSSID
or AP MLD address of the backhaul BSS.
Interfaces of EasyMesh Agents that are downstream of this EasyMesh
Agent are identified by
{{param|BackhaulDown.{i}.BackhaulDownMACAddress}}.
The IEEE 1905 {{bibref|IEEE1905.1a}} Abstraction-Layer ID (ALID)
of the EasyMesh Agent on the network that is
providing the backhaul for this EasyMesh Agent.
EasyMesh Agents that are downstream of this EasyMesh agent are
identified by {{param|BackhaulDown.{i}.BackhaulDownALID}}.
{{list}} Each MAC address is that of a downstream EasyMesh agent's
backhaul link.
{{deprecated|2.19|because it was replaced by
{{param|BackhaulDown.{i}.BackhaulDownMACAddress}}.}}
{{obsoleted|2.21}}
Media type of the backhaul link of this EasyMesh Agent.
This value can be derived from the neighbor's topology response
message 1905 device information type TLV Media Type field
defined in {{bibref|IEEE1905.1a|Table 6-12}}. {{enum}}
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.11b (2.4GHz)
IEEE 802.11g (2.4GHz)
IEEE 802.11a (5GHz)
IEEE 802.11n (2.4GHz)
IEEE 802.11n (5GHz)
IEEE 802.11ac (5GHz)
IEEE 802.11ad (60GHz)
IEEE 802.11af
IEEE 802.11ax
IEEE 802.11be
IEEE 1901 Wavelet
IEEE 1901 FFT
MoCAv1.1
IEEE 802.11ah HaLow
The Physical Layer (PHY) rate in {{units}}
on the backhaul link of this EasyMesh agent.
Indicator of EasyMesh Agent capability to support EasyMesh
{{bibref|EasyMesh}} 802.1Q C-TAG Traffic Separation.
Indicator of the device capability to support Wi-Fi Easy Connect
onboarding.
Indicated in the DPP Onboarding field of the EasyMesh Profile-2
AP Capability TLV {{bibref|EasyMesh}}.
Indicates EasyMesh agent support for running a throughput or latency
test.
0 indicates that the EasyMesh Agent or single-AP does not support
any throughput test and does not support a latency test.
1 indicates that the EasyMesh Agent or single-AP supports a
throughput test but does not support a latency test.
2 indicates that the EasyMesh Agent or single-AP supports a latency
test but does not support a throughput test.
3 indicates that the EasyMesh Agent or single-AP supports a
throughput test and a latency test.
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
The maximum number of MLDs that the EasyMesh Agent can support.
{{bibref|EasyMesh}} source: Wi-Fi 7 Agent Capabilities TLV.
The maximum number of affiliated APs supported by any AP MLD on this
EasyMesh Agent. Set to a value between 0 and 14, which is the number
of affiliated APs minus 1. The value of 15 is reserved.
{{bibref|EasyMesh}} source: Wi-Fi 7 Agent Capabilities TLV.
The maximum number of affiliated bSTAs supported by the bSTA MLD on
this EasyMesh Agent. Set to a value between 0 and 14, which is the
number of affiliated bSTAs minus 1. The value of 15 is reserved.
{{bibref|EasyMesh}} source: Wi-Fi 7 Agent Capabilities TLV.
Indicates the EasyMesh Agent support for TID to Link mapping.
{{bibref|EasyMesh}} source: Wi-Fi 7 Agent Capabilities TLV. {{enum}}
The EasyMesh Agent does not support TID-to-link mapping.
The EasyMesh Agent supports the mapping of each TID to the
same or different link set.
The EasyMesh Agent only supports the mapping of all TIDs to
the same link set.
{{numentries}}
{{numentries}}
The default 802.1Q settings for EasyMesh service prioritization
{{bibref|EasyMesh}}.
Enables or disables default 802.1Q settings.
The primary 802.1Q C-TAG (VLAN ID).
The default Priority Code Point (PCP).
The Service Set Identifier (SSID) to VLAN ID mapping for EasyMesh
traffic separation {{bibref|EasyMesh}}.
Latest Channel Availability Check (CAC) Status Report from the device.
The time this group was collected.
{{numentries}}
{{numentries}}
{{numentries}}
This object describes available channels identified by Channel
Availability Check (CAC).
This is the operating class of an available channel, from
{{bibref|802.11ax|Table E-4}}.
Single channel number of an available channel in the given operating
class.
{{units}} since CAC was completed identifying available channel.
Equals zero for non-DFS channels.
This object describes channels identified by Channel Availability Check
(CAC) that may not be occupied.
Operating class of a channel that is in the non-occupancy list, from
{{bibref|802.11ax|Table E-4}}.
Single channel number in the operating class on which the radar was
detected.
{{units}} remaining in the non-occupancy duration for the channel
specified by the operating class and channel pair.
This object describes channels with ongoing Channel Availability Check
(CAC).
Operating class of a channel that has ongoing CAC, from
{{bibref|802.11ax|Table E-4}}.
Single channel number in the operating class that has an ongoing CAC.
{{units}} remaining to complete the CAC.
This object describes a list of service prioritization (SP) rules
{{bibref|EasyMesh}}.
This object describes the IEEE 1905 security capabilities.
Onboarding protocols supported;
:0: 1905 Device Provisioning Protocol as defined in the EasyMesh
{{bibref|EasyMesh}} 1905 Layer Security Capability TLV.
Message integrity algorithms supported.
: 0: HMAC-SHA256.
Message encryption algorithms supported.
: 0: AES-SIV.
This object contains a table of Wi-Fi 6 {{bibref|802.11ax}} operating
classes, and channels within those operating classes, which have
anticipated channel preference.
Operating Class contains an enumerated value from
{{bibref|802.11ax|Table E-4}}.
The Operating Class per {{bibref|802.11ax|Table E-4}}.
Note that the operating class identifies the band and channel width.
{{list}} The channel numbers in this Operating Class which have
anticipated channel preference.
This object reports Wi-Fi 6 {{bibref|802.11ax}} anticipated medium
usage on channels (and subsets of those channels) on which the device
is operating.
The operating class per {{bibref|802.11ax|Table E-4}}.
The channel number in the given operating class of the channel on
which the anticipated channel usage is reported.
Reference BSSID. Start Time values in this object are referenced to
the Time Sync Function (TSF) timer value indicated in the Timestamp
field in Beacon frames transmitted by this BSSID on the channel.
{{numentries}}
This object reports an entry for anticipated channel usage
{{bibref|802.11ax}}.
Least significant 4 octets of the TSF timer of the Reference BSSID,
at the start of the anticipated first burst of channel usage.
Note: a burst is a continuous or quasi-continuous period of channel
usage. For IEEE 802.11 transmissions, a burst might comprise only one
PPDU, or multiple closely spaced PPDUs.
Duration of each burst of channel usage in {{units}}.
Number of repetitions of the burst of channel usage;
: 0 = single burst,
: 2^32^-1 = indefinite/unknown.
Interval between two successive bursts of channel usage in {{units}};
set to zero if {{param|Repetitions}} is zero.
Bitmask of 26-tone Resource Units (RUs) defined in
{{bibref|802.11ax|Section 27.3.2.2}}, where the (i-1)th bit position
is set to one if the nominal bandwidth of the channel usage
corresponding to this entry fully or partially overlaps with the RUi,
and is otherwise set to zero.
One of:
: MAC address: if the entry corresponds to channel usage by a single
client STA associated to the BSS of the Agent;
: BSSID: if the entry corresponds to channel usage by multiple or
unspecified client STAs associated to the BSS of the Agent;
: BSS Color: (first 42-bits are zero) if the channel usage is caused
by a source external to the BSSs operated by the Agent and the
BSSID cannot be decoded (since frame sent at high MCS) but the BSS
Color in the PHY headers could still be identified;
: Zero: if the channel usage is caused by a source external to the
BSSs operated by the Agent.
Indicates maximum transmit power during each channel usage burst in
{{units}}; equal to 255 when unknown or when the entry corresponds to
multiple transmitters with different transmit powers
The reason for this anticipated channel usage. {{enum}}
TSPEC or other traffic stream with predictable characteristics.
Scheduler policy (if uplink, using Wi-Fi 6 trigger-based
scheduling).
IEEE 802.11 transmitter external to the BSSs operated by the
reporting Agent.
Non-IEEE 802.11, or unknown source.
BSS non-usage (in this special case, a burst is defined as a
continuous period in which the Agent ensures no transmissions
by any of its BSSs on the channel).
This object identifies EasyMesh Agents and their interfaces
that are downstream of this EasyMesh Agent and have backhaul
to this EasyMesh Agent.
The IEEE 1905 {{bibref|IEEE1905.1a}} Abstraction-Layer ID (ALID)
of the EasyMesh Agent on the network that is downstream of
this EasyMesh Agent and has backhaul to this EasyMesh Agent.
MAC address of the EasyMesh Agent's
interface that is downstream of this EasyMesh Agent and
has backhaul to this EasyMesh Agent.
This object contains the Available Spectrum Inquiry request and
response message defined by {{bibref|EasyMesh|Section 8.2.5}}.
This provides information of 6 GHz spectrum availability
as determined by an Automated Frequency Coordination (AFC) system
{{bibref|AFCSDI}}.
One JSON encoded AvailableSpectrumInquiryRequestMessage object as
defined in {{bibref|EasyMesh|Section 8.2.5 and Section 17.2.104
Available Spectrum Inquiry Request TLV}}.
One JSON encoded AvailableSpectrumInquiryResponseMessage object as
defined in {{bibref|EasyMesh|Section 8.2.5 and Section 17.2.105
Available Spectrum Inquiry Response TLV}}.
This object represents an individual Access Point device.
Organizationally unique identifier of the Access Point device
manufacturer. Represented as a six hexadecimal-digit value using all
upper-case letters and including any leading zeros. {{pattern}}
The value MUST be a valid OUI as defined in {{bibref|OUI}}.
This value MUST remain fixed over the lifetime of the device,
including across firmware updates.
If the instance of this {{object}} is the same as {{object|Device.}},
then this parameter is the same as
{{param|Device.DeviceInfo.ManufacturerOUI}}.
{{deprecated|2.18|because it was essentially the same as
{{param|#.Manufacturer}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
The last time that the Access Point device was contacted via the
Multi-AP control protocol.
{{param}} is a reference to the IEEE 1905.1 Network Topology Device.
Since IEEE 1905.1 is a common protocol used by Multi-AP Controllers
for communications, this parameter allows the MultiAP portion of the
data model to reference the associated IEEE 1905.1 portion of the
data model.
This parameter represents the status of Wi-Fi CERTIFIED EasyMeshTM
controller functionality. {{enum}}
{{deprecated|2.18|because it was the same as
{{param|#.ControllerOperationMode}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
Wi-Fi EasyMesh controller is not supported.
Wi-Fi EasyMesh controller is supported but not enabled.
Wi-Fi EasyMesh controller is running.
This parameter represents the status of Wi-Fi CERTIFIED EasyMeshTM
agent functionality. {{enum}}
Wi-Fi EasyMesh agent is not supported.
Wi-Fi EasyMesh agent is supported but not enabled.
Wi-Fi EasyMesh agent is running.
This object represents an individual Access Point device's Backhaul and
unique aspects in the Wi-Fi network.
The endpoints of the backhaul interface are represented by the
(Device's ID and interface MAC Address). This object represents the
upward view of the backhaul interface. The two endpoints of the
backhaul interface are - ({{param|BackhaulDeviceID|deleted}},
{{param|BackhaulMACAddress|deleted}}) of the uplinked Backhaul
Device - {{param|MACAddress|deleted}} of this Access Point Device.
{{empty}} is reserved for the {{object}} instance that represents the
Multi-AP Controller.
The medium being used to backhaul this Access Point Device to the
Backhaul Access Point Device. The {{enum|None}} value is reserved for
the {{object}} instance that represents the Multi-AP Controller.
{{enum}}
{{deprecated|2.18|because it was essentially the same as
{{param|##.BackhaulMediaType}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
The MAC Address at the far end of the backhaul link of the interface
on the network that is providing a backhaul for this Access Point
Device. This along with {{param|BackhaulDeviceID|deleted}}, helps
to identify the backhaul interface endpoint.
{{empty}} is reserved for the {{object}} instance that represents the
Multi-AP Controller.
{{deprecated|2.18|because it was the same as
{{param|##.BackhaulMACAddress}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
The Device's ID of the Device on the network that is providing a
Backhaul Link for this Access Point Device.
{{deprecated|2.18|because it was essentially the same as
{{param|##.BackhaulALID}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
The MAC Address at the near end of the backhaul link of this Access
Point Device's backhaul interface that is connecting via
{{param|##.BackhaulMediaType}} to {{param|BackhaulMACAddress}} of the
Backhaul Device identified by {{param|BackhaulDeviceID}}.
{{deprecated|2.18|because it was the same as
{{param|##.Radio.{i}.BackhaulSta.MACAddress}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
{{numentries}}
Describes one of the current Operating Classes in use by this Radio.
One Opeating Class is indicated for each current Operating Channel
Bandwidth.
The Channel indicated for the 20 MHz Operating Class is equal to the
current primary channel.
The Operating Class per {{bibref|802.11ax|Table E-4}} that this
radio is currently operating on.
This Channel number in the Operating Class that this Radio is
currently operating on.
Nominal Transmit Power EIRP that this radio is currently using for
the current Channel in the Opeating Class.
Represented as 2's complement signed integer in units of decibels
relative to 1 mW ({{units}}).
The time this group was collected.
This object represents the statistics of the backhaul interface view
from the current Device's ID
The total number of bytes transmitted across the backhaul medium (as
identified by the value of the {{param|###.BackhaulMediaType}}
parameter), including framing characters.
The total number of bytes received across the backhaul medium (as
identified by the value of the {{param|###.BackhaulMediaType}}
parameter), including framing characters.
The total number of packets transmitted across the backhaul medium
(as identified by the value of the {{param|###.BackhaulMediaType}}
parameter), including framing characters.
The total number of packets received across the backhaul medium (as
identified by the value of the {{param|###.BackhaulMediaType}}
parameter), including framing characters.
The total number of outbound packets that could not be transmitted
because of errors.
The total number of inbound packets that contained errors preventing
them from being delivered to a higher-layer protocol.
Current utilization (expressed in {{units}}) of the medium (as
identified by the value of the {{param|###.BackhaulMediaType}}
parameter) being
used to backhaul this Access Point device to the Multi-AP Controller.
A value of 0 is used for the {{object}} instance that represents the
Access Point on the Multi-AP Controller.
An indicator of radio signal strength of the backhaul link of the
Access Point (AP) to the Multi-AP Controller, measured in {{units}}.
RCPI is encoded per {{bibref|802.11-2020|Table 9-176}}. The value of
this parameter is indeterminate if the value of the
{{param|###.BackhaulMediaType}} parameter is anything other than
a type of IEEE 802.11 Wi-Fi.
The data transmit rate in {{units}} that was most recently used for
transmission of data from the access point to the associated device.
The data transmit rate in {{units}} that was most recently used for
transmission of data from the associated device to the access point.
The time this group was collected.
This object represents all of the individual Radios contained within
the identified Access Point device known to the controller.
A unique identifier for this particular Radio within the identified
Access Point as defined in {{bibref|DataElements|Section 3.1}}.
Indicates whether this radio is enabled or disabled.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.Radio.{i}.}}, then this parameter is the same as
{{param|Device.WiFi.Radio.{i}.Enable}}.
{{param}} is a reference to the RadioTemplate selected for this
{{object}}.
An indicator of the average radio noise plus interference power
measured for the primary operating channel.
Encoded as defined for ANPI in {{bibref|802.11-2020|Section
11.10.9.4}}.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.Radio.{i}.}}, then this parameter is the same as
{{param|Device.WiFi.Radio.{i}.Stats.Noise}}.
(Total Channel Utililzation) The percentage of time (linearly scaled
with 255 representing 100%) that the Access Point device sensed the
medium was busy, as indicated by either the physical or virtual
carier sense (CS) mechanism. This is essentially the amount of time
spent transmitting (both successful and failed transmissions),
receiving (both local and non-local transmissions), and processing
noise {{bibref|802.11-2020|Section 9.4.2.27}}.
When more than one channel is in use for the BSS operating on the
radio, the {{param}} value is calculated only for the primary
channel.
(Transmit Channel Utilization) The percentage of time (linearly
scaled with 255 representing 100%) that the radio has spent on
sending individually or group addressed transmissions (successful and
failed).
When more than one channel is in use for the BSS operating on the
radio, the {{param}} value is calculated only for the primary
channel.
(Receive Local Channel Utilization) The percentage of time (linearly
scaled with 255 representing 100%) that the radio has spent on
receiving individually or group addressed local transmissions (i.e.
transmissions from any STA associated with any BSS operating on this
radio).
When more than one channel is in use for the BSS operating on the
radio, the {{param}} value is calculated only for the primary
channel.
(Receive Non-Local Channel Utilization) The percentage of time
(linearly scaled with 255 representing 100%) that the radio has spent
on receiving individually or group addressed non-local transmissions
(i.e. valid IEEE 802.11 PPDUs that are not associated with any BSS
operating on this radio).
When more than one channel is in use for the BSS operating on the
radio, the {{param}} value is calculated only for the primary
channel.
Indicates traffic separation on combined fronthaul and Profile-1
backhaul support {{bibref|EasyMesh}}.
Indicates traffic separation on combined Profile-1 backhaul and
Profile-2 backhaul support {{bibref|EasyMesh}}.
Steering Policy:
: 0: Agent Initiated Steering Disallowed;
: 1: Agent Initiated Receive Channel Power Indicator (RCPI)-based
Steering Mandated;
: 2: Agent Initiated RCPI-based Steering Allowed.
Channel Utilization Threshold (defined per Basic Service Set (BSS)
Load element {{bibref|802.11-2020|Section 9.4.2.27}}.).
RCPI Steering Threshold (encoded per {{bibref|802.11-2020|Table
9-176}}).
Station (STA) Metrics Reporting RCPI Threshold.
: 0: Do not report STA Metrics based on RCPI threshold.
: 1 - 220: RCPI threshold (encoded per {{bibref|802.11-2020|Table
9-176}}).
STA Metrics Reporting RCPI Hysteresis Margin Override.
: 0: Use Agent's implementation-specific default RCPI Hysteresis
margin;
: >0: RCPI hysteresis margin value. This field is coded as an
unsigned integer in units of {{units}}.
AP Metrics Channel Utilization Reporting Threshold.
: 0: Do not report AP Metrics based on Channel utilization threshold;
: >0: AP Metrics Channel Utilization Reporting Threshold (similar
to channel utilization measurement in {{bibref|802.11-2020|Section
9.4.2.27}}).
Associated STA Traffic Stats Inclusion Policy.
: {{true}}: Include Associated STA Traffic Stats TLV in AP Metrics
Response.
: {{false}}: Do not include Associated STA Traffic Stats
Type-Length-Value (TLV) in AP Metrics Response;
Associated STA Link Metrics Inclusion Policy.
: {{true}}: Include Associated STA Link Metrics TLV in AP Metrics
Response.
: {{false}}: Do not include Associated STA Link Metrics TLV in AP
Metrics Response;
A string identifying the Wi-Fi chip vendor of this radio in the
device.
Associated Wi-Fi6 STA Status Inclusion Policy.
: {{true}}: include Associated Wi-Fi6 STA Status TLV in AP Metrics
Response.
: {{false}}: do not include Associated Wi-Fi6 STA Status TLV [3] in
AP Metrics Response.
Maximum number of BSSs supported by this radio.
{{bibref|EasyMesh|Section 17.2.7, AP Radio Basic Capabilities TLV}}.
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
{{numentries}}
Contains the Medium Access Control (MAC) address of the STA on this
radio providing Wi-Fi backhaul to this device.
The MAC address of the logical STA sharing the radio for Wi-Fi
backhaul.
This object describes the channel scan capabilities of a radio.
On boot only flag, Indicates whether the specified radio is capable
only of On boot scans.
Scan Impact of using this radio to perform a scan.
: 1: No impact,
: 2: Reduced number of spatial streams,
: 3: Time slicing impairment,
: 4: Radio unavailable for >= 2 seconds.
Minimum Scan Interval, the minimum interval in {{units}} between the
start of two consecutive channel scans on this radio.
{{numentries}}
Table of the operating classes (selected from
{{bibref|802.11ax|Table E-4}}) and channel numbers in each operating
class that the radio is capable of scanning.
The Operating Class per {{bibref|802.11ax|Table E-4}} For 2.4GHz
and 5GHz bands, only 20MHz Operating Classes are valid.
Note that the operating class identifies the band and channel width.
{{list}} The channel numbers in this Operating Class which the radio
is capable of scanning.
This object describes the Channel Availability Check (CAC) capabilities
of a radio.
{{numentries}}
List of Channel Availability Check (CAC) method information for each
type of CAC that the radio can perform. Each type is defined by a
method and time to complete. For each type, the classes and channels
allowed are enumerated.
CAC method supported;
: 0: Continuous CAC,
: 1: Continuous with dedicated radio,
: 2: Multi-Input Multi-Output (MIMO) dimension reduced,
: 3: Time sliced CAC.
Number of {{units}} required to complete this method of CAC.
{{numentries}}
Table of the operating classes (selected from
{{bibref|802.11ax|Table E-4}}) and channel numbers in each operating
class supported for this method of CAC.
The Operating Class per {{bibref|802.11ax|Table E-4}}.
Note that the operating class identifies the band and channel width.
{{list}} The channel numbers in this Operating Class that are
supported for this method of CAC.
This object represents the capabilities of the radio which may be
different from the current operational configuration.
Describes the HT capabilities of the radio as defined by the
AP HTCapabilities TLV {{bibref|EasyMesh|Section 17.2.8}}.
Includes all fields in the AP HTCapabilities TLV except tlvType,
tlvLength, tlvValue and RUID.
Describes the VHT capabilities of the radio as defined by the
AP VHTCapabilities TLV {{bibref|EasyMesh|Section 17.2.9}}.
Includes all fields in the AP VHTCapabilities TLV except tlvType,
tlvLength, tlvValue and RUID.
Describes the HE capabilities of the radio as defined by the
HECapabilities TLV {{bibref|EasyMesh|Section 17.2.10}}.
{{deprecated|2.15|because it is superseded by {{object|WiFi6APRole}}
and {{object|WiFi6bSTARole}}}}
{{obsoleted|2.17}}
{{deleted|2.18}}
This parameter indicates support for Mirrored Stream Classification
Service (MSCS) and EasyMesh configuration of
MSCS {{bibref|EasyMesh|AP Radio Advanced Capabilities TLV}}.
This parameter indicates support for Stream Classification
Service (SCS) and EasyMesh {{bibref|EasyMesh}} configuration of SCS
{{bibref|EasyMesh|AP Radio Advanced Capabilities TLV}}.
This parameter indicates support for QoS Map
{{bibref|EasyMesh|AP Radio Advanced Capabilities TLV}}.
This parameter indicates support for DSCP Mapping Table TLV based
DSCP-to-UP mapping and EasyMesh distribution
of QoS Map elements to associated STAs
{{bibref|EasyMesh|AP Radio Advanced Capabilities TLV}}.
This parameter indicates support for QoS Management Stream
Classification Service (SCS) Traffic Description and EasyMesh
configuration of and/or extensions to SCS using traffic descriptions
{{bibref|EasyMesh|AP Radio Advanced Capabilities TLV}}.
{{numentries}}
{{numentries}}
{{numentries}}
Describes the Wi-Fi 6 capabilities for the AP role.
Describes the Wi-Fi 6 capabilities for the backhaul Station (bSTA)
role.
This object describes the Wi-Fi 7 capabilities for the AP role
including Multi-Link Operation (MLO) capabilities.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the required frequency separation from the
specified radio {{param|RUID}} for MLO
Enhanced Multi-Link Multi-Radio (EMLMR) operation.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the required frequency separation from the
specified radio {{param|RUID}} for MLO
Enhanced Multi-Link Single-Radio (EMLSR) operation.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the required frequency separation from the
specified radio {{param|RUID}} for MLO
Simultaneous Transmit and Receive (STR) operation.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the required frequency separation from the
specified radio {{param|RUID}} for MLO
Non-Simultaneous Transmit and Receive (NSTR) operation.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the Wi-Fi 7 capabilities for the backhaul
Station (bSTA) role including Multi-Link Operation (MLO) capabilities.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the required frequency separation from the
specified radio {{param|RUID}} for MLO
Enhanced Multi-Link Multi-Radio (EMLMR) operation.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the required frequency separation from the
specified radio {{param|RUID}} for MLO
Enhanced Multi-Link Single-Radio (EMLSR) operation.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the required frequency separation from the
specified radio {{param|RUID}} for MLO
Simultaneous Transmit and Receive (STR) operation.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
This object describes the required frequency separation from the
specified radio {{param|RUID}} for MLO
Non-Simultaneous Transmit and Receive (NSTR) operation.
{{bibref|EasyMesh}} Source: Wi-Fi 7 Agent Capabilities TLV.
Authentication and Key Management (AKM) Suite (security mode)
capabilities for the fronthaul BSS.
Authentication and Key Management (AKM) Suite (security mode)
capabilities for the backhaul BSS.
Describes one of the possible Operating Classes supported by this
Radio.
The Operating Class per {{bibref|802.11ax|Table E-4}} that this
radio is capable of operating on.
Maximum Transmit Power EIRP that this radio is capable of
transmitting in the current regulatory domain for the Operating
Class.
Represented as 2's complement signed integer in units of decibels
relative to 1 mW ({{units}}).
{{list}} The channel numbers which are statically non-operable in the
Operating Class (i.e. the Radio is never able to operate on these
channels).
Other channels from this Operating Class which are not listed here
are supported for the Radio.
The number of non-operable channels contained in
{{param|NonOperable}}.
This object describes the capabilities of the Wi-Fi HaLow radio,
most of which can be extracted from the Sub 1 GHz (S1G) capabilities
Information Element (IE) in {{bibref|802.11-2020|Section 9.4.2.200.2}}.
Indicates if this Wi-Fi HaLow radio accepts sensor associated
devices (STAs).
Indicates if this Wi-Fi HaLow radio accepts non-sensor associated
devices (STAs).
Describes one of the current Operating Classes in use by this Radio.
One Operating Class is indicated for each current Operating Channel
Bandwidth.
The Channel indicated for the 20 MHz Operating Class is equal to the
current primary channel.
The Operating Class per {{bibref|802.11ax|Table E-4}} that this
radio is currently operating on.
This Channel number in the Operating Class that this Radio is
currently operating on.
Nominal Transmit Power EIRP that this radio is currently using for
the current Channel in the Opeating Class.
Represented as 2's complement signed integer in units of decibels
relative to 1 mW ({{units}}).
This is the upper limit on nominal transmit Equivalent Isotropically
Radiated Power (EIRP) that this radio is allowed to use for the
current {{param|Class}}. In units of decibels relative to 1 mW
{{units}}.
The time this group was collected. Formatted with the date-and-time
string format as defined in {{bibref|RFC3339|Section 3}}.
The operating classes, and list of channels for each operating class,
which are not allowed to be used on this radio.
Enables or disables disallowed operating classes and channels.
The Operating Class per {{bibref|802.11ax|Table E-4}}.
Note that the operating class identifies the band and channel width.
{{list}} The channel numbers in this Operating Class that are not
allowed to be used on this radio.
Values represent Channel Preference TLV values in the most recent
Channel Preference Report message {{bibref|EasyMesh|17.2.13}}.
Each entry in this table describes one of the operating classes
for which Channel Preference has been reported.
A Preference score of 15 must be inferred for all channel/operating
classes not present in this table, unless that channel/operating class
has been reported as statically non-operable in the most recent
AP Radio Basic Capabilities TLV {{bibref|EasyMesh|17.2.7}}.
The operating class {{bibref|802.11ax|Table E-4}}.
Note that the operating class identifies the band and channel width.
Values represent the OpClass field of the
Channel Preference TLV in the most recent Channel Preference Report
message {{bibref|EasyMesh|17.2.13}}.
The channel numbers in this operating class.
{{list}} Values represent the Channel List field of the
Channel Preference TLV in the most recent Channel Preference Report
message {{bibref|EasyMesh|17.2.13}}.
The reported preference for this {{param|OpClass}} and
{{param|ChannelList}}, as defined in {{bibref|EasyMesh|17.2.13}}.
Values represent the Preference field of the Channel
Preference TLV in the most recent Channel Preference Report
message {{bibref|EasyMesh|17.2.13}}.
Reason Code. Indicates the reason for the {{param|Preference}},
as defined in {{bibref|EasyMesh|17.2.13}}.
Values represent the Reason_Code field of the
Channel Preference TLV in the most recent Channel Preference Report
message {{bibref|EasyMesh|17.2.13}}.
The spatial reuse configuration of this radio. Applies only to Wi-Fi 6
{{bibref|802.11ax}} and possibly later generations of radios.
Acronyms: Spatial Reuse Group (SRG), Overlapping Basic Service Set
(OBSS), Preamble Detection (PD).
The value of the Partial Basic Service Set (BSS) Color subfield of
the HEOperations.BSSColorInformation field being transmitted by BSSs
operating on this radio. (EasyMesh TLV Field: Partial BSS Color)
Bitmap of BSS colors of Overlapping BSSs (OBSSs) that the
High-Efficiency (HE) AP has identified by itself or via the
autonomous BSS Color collision reports received from associated
non-AP HE STAs.
A single logical BSS operating on this radio.
The MAC Address of the logical BSS (BSSID).
If the instance of this {{object}} is the same as
{{object|Device.WiFi.SSID.{i}.}}, then this parameter is the same as
{{param|Device.WiFi.SSID.{i}.BSSID}}.
The SSID in use for this BSS.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.SSID.{i}.}}, then this parameter is the same as
{{param|Device.WiFi.SSID.{i}.SSID}}.
Whether the BSSID is currently enabled (beaconing frames are being
sent) or disabled.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.SSID.{i}.}}, then this parameter is the same as
{{param|Device.WiFi.SSID.{i}.Enable}}.
{{param}} is a reference to the BSSTemplate selected for this
{{object}}.
{{param}} is a reference to the SecurityTemplate selected for this
{{object}}.
Time in {{units}} since the last change to the {{param|Enabled}}
value.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.SSID.{i}.}}, then this parameter is the same as
{{param|Device.WiFi.SSID.{i}.LastChange}}.
The time this group was collected. Formatted with the date-and-time
string format as defined in {{bibref|RFC3339|Section 3}}.
Access Point (BSS) wide statistics for total unicast bytes
transmitted.
This counter does not include Multi-Link Device (MLD) traffic
through this BSS.
Access Point (BSS) wide statistics for total unicast bytes received.
This counter does not include MLD traffic through this BSS.
Access Point (BSS) wide statistics for total multicast bytes
transmitted.
This counter does not include MLD traffic through this BSS.
Access Point (BSS) wide statistics for total multicast bytes
received.
This counter does not include MLD traffic through this BSS.
Access Point (BSS) wide statistics for total broadcast bytes
transmitted.
This counter does not include MLD traffic through this BSS.
Access Point (BSS) wide statistics for total broadcast bytes
received.
This counter does not include MLD traffic through this BSS.
Byte Counter Units.
: 1: kibibytes (KiB)
: 2: mebibytes (MiB).
Profile-1 Backhaul STA association disallowed.
: {{true}}: Backhaul STA association disallowed;
: {{false}}: Backhaul STA association allowed.
Profile-2 Backhaul STA association disallowed.
: {{true}}: Profile 2 bSTA disallowed;
: {{false}}: Profile 2 bSTA allowed.
The status of allowance of new client device associations on this
BSS.
: 0: No more associations allowed,
: 1: Associations allowed.
Estimated Service Parameters information field for AC=BE, defined per
{{bibref|802.11-2020|Figure 9-637}} and referenced in
{{bibref|EasyMesh|Section 17.2.22}}.
Estimated Service Parameters information field for AC=BK, defined per
{{bibref|802.11-2020|Figure 9-637}} and referenced in
{{bibref|EasyMesh|Section 17.2.22}}.
Estimated Service Parameters information field for AC=VI, defined per
{{bibref|802.11-2020|Figure 9-637}} and referenced in
{{bibref|EasyMesh|Section 17.2.22}}.
Estimated Service Parameters information field for AC=VO, defined per
{{bibref|802.11-2020|Figure 9-637}} and referenced in
{{bibref|EasyMesh|Section 17.2.22}}.
Indicates that this BSS is in use as a backhaul BSS;
: {{true}}: backhaul BSS in use,
: {{false}}: backhaul BSS not in use.
In {{bibref|EasyMesh}} 0 is in use and 1 is not in use.
Indicates that this BSS is in use as a fronthaul BSS;
: {{true}}: fronthaul BSS in use,
: {{false}}: fronthaul BSS not in use.
In {{bibref|EasyMesh}} 0 is in use and 1 is not in use.
Multi-AP Profile-1 [3] (R1) disallowed status.
: {{true}}: disallowed,
: {{false}}: allowed.
In {{bibref|EasyMesh}} 0 is allowed and 1 is disallowed.
Multi-AP Profile-2 [3] (R2) disallowed status.
: {{true}}: disallowed,
: {{false}}: allowed.
In {{bibref|EasyMesh}} 0 is allowed and 1 is disallowed.
Multiple BSSID Set;
: {{true}}: configured,
: {{false}}: not-configured.
In {{bibref|EasyMesh}}, 1 is configured and 0 is not-configured.
Transmitted BSSID;
: {{true}}: transmitted,
: {{false}}: non-transmitted.
In {{bibref|EasyMesh}}, 1 is transmitted and 0 is non-transmitted.
{{list}} List items indicate Authentication and Key Management (AKM)
suites/security modes allowed at this BSS for fronthaul. {{enum}}
"psk" indicates one or more of the PSK and FT-PSK AKMs defined
in {{bibref|802.11-2020|Table 9-151}} typically at least
"00-0F-AC:2" for interoperability.
"dpp" indicates one or more of the DPP and FT-DPP AKMs defined
in {{bibref|EasyConnect|Section 8.4}}, typically at least
"50-6F-9A:2" for interoperability.
"sae" indicates one or more of the SAE and FT-SAE AKMs defined
in {{bibref|802.11-2020|Table 9-151}} typically at least
"00-0F-AC:8" for interoperability.
"SuiteSelector" indicates an AKM suite selector, the value of
which is indicated in {{param|FronthaulSuiteSelector}}.
AKM suite selector, the AKM suite selector (OUI and type) is
encoded as a 4-octet hex-encoded value without internal
delimiters, e.g. 506F9A02 {{bibref|802.11-2020|Table 9-151}}.
This parameter applies if {{param|FronthaulAKMsAllowed}} includes
value "SuiteSelector".
{{list}} List items indicate Authentication and Key Management (AKM)
suites/security modes allowed at this BSS for backhaul. {{enum}}
"psk" indicates one or more of the PSK and FT-PSK AKMs defined
in {{bibref|802.11-2020|Table 9-151}} typically at least
"00-0F-AC:2" for interoperability.
"dpp" indicates one or more of the DPP and FT-DPP AKMs defined
in {{bibref|EasyConnect|Section 8.4}}, typically at least
"50-6F-9A:2" for interoperability.
"sae" indicates one or more of the SAE and FT-SAE AKMs defined
in {{bibref|802.11-2020|Table 9-151}} typically at least
"00-0F-AC:8" for interoperability.
"SuiteSelector" indicates an AKM suite selector, the value of
which is indicated in {{param|BackhaulSuiteSelector}}.
AKM suite selector, the AKM suite selector (OUI and type) is
encoded as a 4-octet hex-encoded value without internal
delimiters, e.g. 506F9A02 {{bibref|802.11-2020|Table 9-151}}.
This parameter applies if {{param|BackhaulAKMsAllowed}} includes
value "SuiteSelector".
{{list}} The current basic data rates; the set of data rates,
in {{units}}, that have to be supported by all stations that desire
to join this BSS. The stations have to be able to receive and
transmit at each of the data rates listed in {{param}}.
Most control packets use a data rate in {{param}}.
{{numentries}}
{{numentries}}
This object contains a table of {{param|DescriptorElement}}.
The BSSID of BSS for which this descriptor applies.
MAC address of STA for which this descriptor applies.
The descriptor element. One of:
: MSCS descriptor element (as described in
{{bibref|802.11-2020|Section 9.4.2.243}}, or
: SCS descriptor element (as described in
{{bibref|802.11-2020|Section 9.4.2.121}}, or
: QoS Management DSCP policy element (as described in
{{bibref|802.11-2020|Section 9.4.2.94}} and
{{bibref|RFC8325|Section 6.3}}).
This object represents an individual Access Point Radio in the Wi-Fi
network.
{{list}} List items represent channels in the non-occupancy list due
to radars detected by Dynamic Frequency Selection (DFS) Channel
Availability Check (CAC).
{{deprecated|2.18|because it was superseded by
{{object|##.CACStatus.{i}.}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
This object provides Multiuser (MU)-specific BSS configuration.
This object provides packet statistics for a Multiuser (MU) BSS.
A single logical Access Point operating on this radio.
Number of times a Blacklist steer was attempted for this Access
Point.
Blacklist steering is the process of forcing a connected STA to move
to another Access Point by temporarily blocking its access to the
current Access Point.
Number of times a BTM (BSS Transition Management; {{bibref|802.11-2020|sections 4.3.19.3 and 6.3.57}}
steer was attempted for this Access Point.
Number of asynchronous BTM (BSS Transition Management;
{{bibref|802.11-2020|sections 4.3.19.3 and 6.3.57}} Queries for which a BTM Request was issued by
this Access Point.
This object contains Wi-Fi Protected Setup (WPS)
Push Button Configuration (PBC) configuration and status
as specified in {{bibref|WPSv1.0}} or {{bibref|WPS 2.0}}).
In EasyMesh {{bibref|EasyMesh}} this object applies to fronthaul only.
Enables or disables WPS functionality for this EasyMesh agent or
single AP.
Indicates the current status of WPS. If the device goes to
{{enum|SetupLocked}} the WPS needs to be disabled and re-enabled to
come out of this state.
Object containing the results of the most recent throughput (speed)
test from the BSS to a station (STA).
Timestamp for the throughput test, indicating when the test
completed.
MAC address of the STA that the throughput test ran to.
The VLAN ID (VID) that the throughput test ran on.
A value of 0 indicates that no VLAN was specified.
Wireless MultiMedia (WMM) User Priority (UP) {{bibref|WMM}}
that the throughput test was requested to run on.
A value of 8 indicates that no UP was specified.
Duration of the throughput test in {{units}}.
The OSI layer that the throughput test ran on.
The test algorithm that the throughput test used.
Downlink speed found by the throughput test in {{units}}.
Uplink speed found by the throughput test in {{units}}.
Object containing the results of the most recent latency test set
from the BSS to a station (STA). Each latency test set includes a
number of individual echo tests. Each echo test result provides a
sample of round-trip times and statistics on all the echo tests
in this latency test are reported in this object.
Timestamp for the latency test, indicating when the last echo in
the latency test set was received or timed-out.
MAC address of the station (STA) or EasyMesh Agent
that the latency test ran to.
The VLAN ID (VID) that the latency test ran on.
A value of 0 indicates that no VLAN was specified.
Wireless MultiMedia (WMM) User Priority (UP) {{bibref|WMM}}
that the latency test was requested to run on.
A value of 8 indicates that no UP was specified.
The size of each data block, in {{units}}, that was transmitted
in each echo test. The data block excludes the packet or frame
header.
A value of 0 indicates that no DataBlockSize was specified.
The OSI layer that the latency test ran on.
The test algorithm that the latency test used.
The number of successfully received echo responses.
This parameter is an output of the latency test.
The number of lost echoes in the latency test set.
This parameter is an output of the latency test.
The average round-trip time of the results of the latency test set
in {{units}}. This average is across successfully received echoes
only.
This parameter is an output of the latency test.
The minimum round-trip time of the results of the latency test set
in {{units}}. This minimum is across successfully received echoes
only.
This parameter is an output of the latency test.
The maximum round-trip time of the results of the latency test set
in {{units}}. This maximum is across successfully received echoes
only.
This parameter is an output of the latency test.
This object records inputs for setting QoS Management
{{bibref|EasyMesh|Section 20}}.
Indicates whether QoS Map is enabled on this BSS.
Indicates whether Mirrored Stream Classification Service (MSCS)
is enabled on this BSS.
Indicates whether Stream Classification Service (SCS)
is enabled on this BSS.
Indicates whether DSCP Policy is enabled on this BSS.
Indicates whether the extensions to SCS using Traffic Descriptions
is enabled on this BSS.
Object describing a single Associated Device (STA).
The Backhaul STAs (bSTAs) with which other
{{object|Device.WiFi.DataElements.Network.Device.{i}.}} connect to this BSS are included
in this table.
STA MLD and bSTA MLD are not included, and are instead part of
{{object|Device.WiFi.DataElements.Network.Device.{i}.APMLD.{i}.STAMLD.{i}.}}.
AffiliatedSTAs and AffiliatedbSTAs are not included, and are instead part of
{{object|Device.WiFi.DataElements.Network.Device.{i}.APMLD.{i}.STAMLD.{i}.AffiliatedSTA.{i}.}}.
The MAC address of an associated device.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.MACAddress}}.
The time this group was collected. Formatted with the date-and-time
string format as defined in {{bibref|RFC3339|Section 3}}.
Describes the HT capabilities of the Associated Device (STA).
Uses the format defined by the AP HTCapabilities TLV
{{bibref|EasyMesh|Section 17.2.8}}.
Includes all fields in the AP HTCapabilities TLV except tlvType,
tlvLength, tlvValue and RUID.
Describes the VHT capabilities of the Associated Device (STA).
Uses the format defined by the AP VHTCapabilities TLV
{{bibref|EasyMesh|Section 17.2.9}}.
Includes all fields in the AP VHTCapabilities TLV except tlvType,
tlvLength, tlvValue and RUID.
Describes the HE capabilities of the Associated Device (STA).
{{deprecated|2.15|because it is superseded by
{{object|WiFi6Capabilities}}}}
{{obsoleted|2.17}}
{{deleted|2.18}}
The frame body of the most recently received (Re)Association Request
frame from this client (STA), as defined in Table 9-34 and Table 9-36
of {{bibref|802.11-2020}} in the order of the underlying referenced
standard.
The data transmit rate in {{units}} that was most recently used for
transmission of data from the access point to the associated device.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.LastDataDownlinkRate}}.
The data transmit rate in {{units}} that was most recently used for
transmission of data from the associated device to the access point.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.LastDataUplinkRate}}.
The amount of time in {{units}} that the Radio has spent on the
Channel receiving data from this Associated Device (STA).
The amount of time in {{units}} that the Radio has spent on the
Channel transmitting data to this Associated Device (STA).
Estimate of the MAC layer throughput in {{units}} achievable in the
downlink direction if 100% of channel airtime and BSS operating
bandwidth were available, as defined in {{bibref|EasyMesh|Section
10.3.1}}.
Estimate of the MAC layer throughput in {{units}} achievable in the
uplink direction if 100% of channel airtime and BSS operating
bandwidth were available, as defined in {{bibref|EasyMesh|Section
10.3.1}}.
An indicator of radio signal strength of the uplink from the
associated STA to the access point - measured in {{units}}. RCPI is
encoded per {{bibref|802.11-2020|Table 9-176}}, and described in
{{bibref|EasyMesh|Section 10.3.1}}). Reserved: 221 - 255.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.SignalStrength}}.
The time in {{units}} since this Associated Device (STA) was
associated.
The total number of bytes transmitted to the Associated Device.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.BytesSent}}.
The total number of bytes received from the Associated Device.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.BytesReceived}}.
The total number of packets transmitted to the Associated Device.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.PacketsSent}}.
The total number of packets received from the Associated Device.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.PacketsReceived}}.
The total number of outbound packets that could not be transmitted
because of errors. These might be due to the number of
retransmissions exceeding the retry limit, or from other causes.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.ErrorsSent}}.
The total number of inbound packets that contained errors preventing
them from being delivered to a higher-layer protocol.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.ErrorsReceived}}.
The total number of transmitted packets which were retransmissions.
Two retransmissions of the same packet results in this counter
incrementing by two.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Stats.RetransCount}}.
{{list}} Measurement Report element(s) received from the Associated
Device (STA) that constitute the latest Beacon report as defined in
{{bibref|802.11-2020|Figure 9-230}}.
The number of measurement report elements contained in
{{param|MeasurementReport}}.
IPV4 Address assigned to the client.
IPV6Address assigned to the client.
Hostname assigned to the client.
This is the Cellular Data Preference for a Agile Multiband (AMB)
capable STA This specifies the use of the cellular data connection.
{{bibref|AMB}} {{enum}}
Re-association Delay {{bibref|AMB}}. The time, in {{units}}, after a
BTM steer from AP1 to AP2 during which the station cannot go back and
re-associate with AP1.
This parameter indicates the current operating sleep mode
as recorded by the BSS {{bibref|802.11-2020}}. {{enum}}
This parameter indicates the current operating security state as
defined in {{bibref|802.11-2020|Section 12.6.1.1}}. {{enum}}
Pairwise AKM suite selector selected by the associated device (STA).
The Pairwise AKM suite selector (OUI and type) is encoded as a 4-octet
hex-encoded value without internal delimiters, e.g. 506F9A02
{{bibref|802.11-2020|Table 9-151}}.
Pairwise AKM cipher selector selected by the associated device (STA).
The Pairwise AKM cipher selector (OUI and type) is encoded as a 4-octet
hex-encoded value without internal delimiters, e.g. 506F9A02
{{bibref|802.11-2020|Table 9-149, OUI field}}.
The RSN Capabilities selected by the STA during association
{{bibref|802.11-2020|Section 9.4.2.24.4,}}.
{{numentries}}
The summary of statistics and operations for an individual STA on the
Wi-Fi network.
The counters contained in {{object}} are all reset on reboot.
Date and time in UTC when the device was associated.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.AssociationTime}}.
{{deprecated|2.18|because it was essentially the same as
{{param|#.LastConnectTime}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
An indicator of the average radio noise plus interference power
measured on the uplink from the Associated Device (STA) to the Access
Point (AP).
Encoded as defined for ANPI in {{bibref|802.11-2020|Section
11.10.9.4}}.
If the instance of this {{object}} is the same as
{{object|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.}}, then
this parameter is the same as
{{param|Device.WiFi.AccessPoint.{i}.AssociatedDevice.{i}.Noise}}.
{{deprecated|2.18|because it should be the same as
{{param|###.Noise}}.}}
{{obsoleted|2.20}}
{{deleted|2.21}}
{{numentries}}
The summary of statistics related to Multi-AP Steering for this STA on
the Wi-Fi network.
The counters contained in {{object}} are all reset on reboot.
Number of times this Associated Device should have been steered but
wasn't because a better candidate AP couldn't be found.
Number of times a Blacklist steer was attempted on this Associated
Device.
Number of times an attempted Blacklist steer succeeded for this
Associated Device.
Number of times an attempted Blacklist steer failed for this
Associated Device.
Number of times a BTM (BSS Transition Management; {{bibref|802.11k}})
steer was attempted on this Associated Device.
Number of times an attempted BTM (BSS Transition Management;
{{bibref|802.11k}}) steer succeeded for this Associated Device.
Number of times an attempted BTM (BSS Transition Management;
{{bibref|802.11k}}) steer failed for this Associated Device.
Number of asynchronous BTM (BSS Transition Management;
{{bibref|802.11k}}) Queries for which a BTM Request was issued to
this Associated Device.
The number of {{units}} since this Associated Device was last
attempted to be steered.
The history of Multi-AP Steering for this STA on the Wi-Fi network.
The contents of this multi-instance object are reset on reboot.
The date/time when steering was initiated for the Associated Device.
The BSSID of the Access Point that initiated the steering.
The type of event that caused the steering to be initiaited. {{enum}}
NOTE: This might be Unknown for BTM Query Response steers.
The type of steering that was attempted. {{enum}}
The BSSID of the destination Access Point of a successful steer.
A failed steering attempt will leave this parameter {{empty}}.
The amount of time in {{units}} required for the steer to complete
successfully.
A failed steering attempt will leave this parameter 0.
Describes the Wi-Fi 6 capabilities of the Associated Device (STA).
Describes the HaLow capabilities of the Associated Device (STA).
most of which can be extracted from the Sub 1 GHz (S1G) capabilities
Information Element (IE) in {{bibref|802.11-2020|Section 9.4.2.200.2}}.
Indicates if this is a sensor device.
A value of {{false}} indicates this is a non-sensor device.
Object describing Traffic Identifiers (TIDs), and Queue Size for each
TID, for this Associated Device (STA).
The TID of the corresponding Queue Size field.
Queue Size for this TID. Its format is defined in Table 9-10-QoS
Control field {{bibref|802.11-2020}}.
Each instance represents a station (STA) that has been discovered by
the Radio but is not associated to any of the BSS operating on the
Radio.
The MAC address of the Non-AP STA.
An indicator of radio signal strength (RCPI) of the uplink from the
Non-AP STA - measured in {{units}}. RCPI is encoded per
{{bibref|802.11-2020|Table 9-176}}, and described in
{{bibref|EasyMesh|Section 10.3.2}}. Reserved: 221 - 255.
Operating class on which this unassociated STA was last detected,
per {{bibref|802.11ax|Table E-4}}.
Channel on which this unassociated STA was last detected.
This object contains the events generated when a STA associates to a
BSS.
{{numentries}}
{{deprecated|2.17|because a corresponding USP event is defined instead}}
{{obsoleted|2.19}}
{{deleted|2.20}}
The events generated when an Associated Device (STA) associates to a
BSS.
{{deprecated|2.17|because a corresponding USP event is defined instead}}
{{obsoleted|2.19}}
{{deleted|2.20}}
Describes the Wi-Fi 6 capabilities of the Associated Device (STA).
{{deprecated|2.17|because a corresponding USP event is defined instead}}
{{obsoleted|2.19}}
{{deleted|2.20}}
This object contains the events generated when an Associated Device
(STA) disassociates from a BSS.
{{numentries}}
{{deprecated|2.17|because a corresponding USP event is defined instead}}
{{obsoleted|2.19}}
{{deleted|2.20}}
The events generated when an Associated Device (STA) disassociates from
a BSS.
{{deprecated|2.17|because a corresponding USP event is defined instead}}
{{obsoleted|2.19}}
{{deleted|2.20}}
This object contains the events generated when a Station (STA) fails to
connect to a Basic Service Set (BSS).
{{numentries}}
{{deprecated|2.17|because a corresponding USP event is defined instead}}
{{obsoleted|2.19}}
{{deleted|2.20}}
This object describes the data provided with a failed connection event
{{deprecated|2.17|because a corresponding USP event is defined instead}}
{{obsoleted|2.19}}
{{deleted|2.20}}
{{numentries}}
{{numentries}}
{{numentries}}
The list of neighboring Access Points discovered by a Radio organized
per Operating Class and Channel tuple.
The timestamp of the last scan. Formatted with the date-and-time
string format as defined in {{bibref|RFC3339|Section 3}}.
Total time spent performing the scan of this channel in {{units}}.
{{deprecated|2.21|because it is was moved to
{{object|OpClassScan.{i}.ChannelScan.{i}}}.}}
Indicates whether the scan was performed passively (false)
or with active probing (true).
{{deprecated|2.21|because it is was moved to
{{object|OpClassScan.{i}.ChannelScan.{i}}}.}}
The Operating Class of neighboring Access Points discovered by a Radio
during a channel scan.
The Operating Class per {{bibref|802.11ax|Table E-4}} of the
OpClass and Channel tuple scanned by the Radio. For 2.4GHz and 5GHz
bands, only 20MHz Operating Classes are valid.
Note that the Operating Class identifies the band and channel width.
The Channel associated with an Operating Class of neighboring Access
Points discovered by a Radio during a channel scan.
The channel number of the Channel scanned by the Radio given the
Operating Class.
The timestamp of the last scan of the channel. Formatted with the
date-and-time string format as defined in {{bibref|RFC3339|Section
3}}.
Total time spent performing the scan of this channel in {{units}}.
Indicates the scan method used: {{true}} if active probing was
employed, or {{false}} if the scan was performed passively.
The current Channel Utilization measured by the Radio on the scanned
20MHz channel, as defined by {{bibref|802.11-2020|Section 9.4.2.27}}.
An indicator of the average radio noise plus interference power
measured for the primary operating channel.
Encoded as defined for ANPI in {{bibref|802.11-2020|Section
11.10.9.4}}.
Status code to indicate whether a scan has been performed and if not
the reason for failure {{enum}}
Success
Scan not supported on this
opclass and channel Request too soon after last
scan Radio too busy to perform scan
Scan not completed
Scan aborted
Fresh scan not supported,
radio only supports on boot scans reserved
The neighboring BSS discovered by a Radio during a channel scan.
For MLDs, {{param|MLDMACAddress}} identifies the AP MLD for which this
NeighborBSS.{i}. is an affilated AP, other affiliated APs in this
{{object}} have the same value of {{param|MLDMACAddress}}.
The BSSID indicated by the neighboring BSS.
The SSID indicated by the neighboring BSS.
An indicator of radio signal strength (RSSI) of the Beacon or Probe
Response frames of the neighboring BSS as received by the radio
measured in {{units}}. (RSSI is encoded per
{{bibref|802.11-2020|Table 9-176}}). Reserved: 221 - 255.
Indicates the maximum bandwidth at which the neighboring BSS is
operating. e.g. "1" or "2" or "4" or "8"” or "16" or "20" or "40"
or "80" or "80+80" or "160" or "320" MHz.
The channel utilization reported by the neighboring BSS per the BSS
Load element if present in Beacon or Probe Response frames, as
defined by {{bibref|802.11-2020|Section 9.4.2.27}}.
The number of Associated Devices (STA) reported by this neighboring
BSS per the BSS Load element if present in Beacon or Probe Response
frames as defined by {{bibref|802.11-2020|Section 9.4.2.27}}.
The Multi-Link Device (MLD) MAC address of the
Multi-Link Operation (MLO) capable access point this
neighboring BSS is affiliated to.
Null if the neighboring BSS is not an affiliated AP.
The BSSID of the reporting BSSID if different from {{param|BSSID}}.
This will be set if the NeigborBSS was discovered through,
for example, a Reduced Neighbor Report.
EasyMesh {{bibref|EasyMesh}} source: Channel Scan Result TLV.
Indicates if the neighboring BSS is part of a MultiBSSID set
and may be a non-transmitted BSSID.
Set to true if the neighbour BSS Beacon/Probe Responses include a
BSSLoad Element as defined in
{{bibref|802.11-2020|Section 9.4.2.28}}.
Set to the BSS Color from the BSS Color Information field in the
BSS's HE Operation element.
The time this event happened. Formatted with the date-and-time string
format as defined in {{bibref|RFC3339|Section 3}}.
If a MLD, the MAC Address of the AP MLD, otherwise the MAC Address
of the logical BSS (BSSID) which is reporting the Association Event.
If a MLD, the MAC Address of the STA MLD, otherwise
the MAC Address of the Associated Device (STA).
The status code sent to the Associated Device (STA) in the Association
Response frame as defined by {{bibref|802.11-2020|Table 9-50}}.
Describes the HT capabilities of the Associated Device (STA).
Uses the format defined by the AP HTCapabilities TLV
{{bibref|EasyMesh|Section 17.2.8}}.
Includes all fields in the AP HTCapabilities TLV except tlvType,
tlvLength, tlvValue and RUID.
Describes the VHT capabilities of the Associated Device (STA).
Uses the format defined by the AP VHTCapabilities TLV
{{bibref|EasyMesh|Section 17.2.9}}.
Includes all fields in the AP VHTCapabilities TLV except tlvType,
tlvLength, tlvValue and RUID.
Describes the HE capabilities of the Associated Device (STA).
{{deprecated|2.16|because it is superseded by
{{object|WiFi6Capabilities}}.}}
{{obsoleted|2.18}}
{{deleted|2.19}}
The frame body of the (Re)Association Request frame received from this
client (STA), as defined in Table 9-34 and Table 9-36 of
{{bibref|802.11-2020}} in the order of the underlying referenced
standard.
Operating class in use at the time of this event, from
{{bibref|802.11ax|Table E-4}}. May be determined from
{{bibref|EasyMesh|Table 17.2.17, Operating Channel Report TLV}}
and the Supported Operating Classes element in
{{bibref|EasyMesh|Table 17.2.19, Client Capability Report TLV}}.
For Multi-Link Operation (MLO) this is the operating class over
which association messaging had occurred.
The single channel number of the channel in use at the time of
this event. May be determined from
{{bibref|EasyMesh|Table 17.2.17, Operating Channel Report TLV}}
and the Supported Operating Classes element in
{{bibref|EasyMesh|Table 17.2.19, Client Capability Report TLV}}.
For Multi-Link Operation (MLO) this is the channel over
which association messaging had occurred.
If a MLD, the MAC Address of the AP MLD, otherwise the MAC Address
of the logical BSS (BSSID) which is reporting the Disassociation Event.
If a MLD, the MAC Address of the STA MLD, otherwise
the MAC Address of the Associated Device (STA).
The Reason Code received by the AP from the Associated Device (STA) in
the most recent Disassociation or Deauthentication frame or sent by the
AP to the Associated Device (STA) in the most recent Disassociation or
Deauthentication frame as defined in {{bibref|802.11-2020|Table 9-49}}.
The total number of bytes transmitted to the Associated Device (STA).
For Multi-AP Agents that implement Profile-1, the units of this
counter are Bytes. Otherwise, the units of this counter are as
specified by
{{param|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.ByteCounterUnits}}.
The total number of bytes received from the Associated Device (STA).
For Multi-AP Agents that implement Profile-1, the units of this
counter are Bytes. Otherwise, the units of this counter are as
specified by
{{param|Device.WiFi.DataElements.Network.Device.{i}.Radio.{i}.BSS.{i}.ByteCounterUnits}}.
The total number of packets transmitted to the Associated Device (STA).
The total number of packets received from the Associated Device (STA).
The total number of outbound packets that could not be transmitted to
the Associated Device (STA) because of errors. These might be due to
the number of retransmissions exceeding the retry limit or from other
causes.
The total number of inbound packets from the Associated Device (STA)
that contained errors preventing them from being delivered to a
higher-layer protocol.
The total number of transmitted packets to the Associated Device (STA)
which were retransmissions.
N retransmissions of the same packet results in this counter
incrementing by N.
The time this event happened. Formatted with the date-and-time string
format as defined in {{bibref|RFC3339|Section 3}}.
The data transmit rate in {{units}} that was most recently used for
transmission of data from the access point to the Associated Device
(STA).
The data transmit rate in {{units}} that was most recently used for
transmission of data from the Associated Device (STA) to the access
point.
The amount of time in {{units}} that the Radio has spent on the
Channel receiving data from the Associated Device (STA).
The amount of time in {{units}} that the Radio has spent on the
Channel transmitting data to the Associated Device (STA).
Estimate of the MAC layer throughput in {{units}} achievable in the
downlink direction to the Associated Device (STA)
if 100% of channel airtime and BSS operating bandwidth
were available, as defined in {{bibref|EasyMesh|Section 10.3.1}}.
Estimate of the MAC layer throughput in {{units}} achievable in the
uplink direction from the Associated Device (STA) if 100% of channel
airtime and BSS operating bandwidth were available, as defined in
{{bibref|EasyMesh|Section 10.3.1}}.
An indicator of radio signal strength of the uplink from the
Associated Device (STA) to the access point - measured in {{units}}.
RCPI is encoded per {{bibref|802.11-2020|Table 9-176}}, and described
in {{bibref|EasyMesh|Section 10.3.1}}). Reserved: 221 - 255.
The time in {{units}} since this Associated Device (STA) was
associated.
An indicator of the average radio noise plus interference power
at the access point measured for the primary operating channel
to this Associated Device (STA).
Encoded as defined for ANPI in
{{bibref|802.11-2020|Section 11.10.9.4}}.
This parameter indicates the entity that initiated this
Disassociation Event. {{enum}}
Operating class in use at the time of this event, from
{{bibref|802.11ax|Table E-4}}. May be determined from
{{bibref|EasyMesh|Table 17.2.17, Operating Channel Report TLV}}
and the Supported Operating Classes element in
{{bibref|EasyMesh|Table 17.2.19, Client Capability Report TLV}}.
For Multi-Link Operation (MLO) this is the operating class over
which association messaging had occurred.
The single channel number of the channel in use at the time of
this event. May be determined from
{{bibref|EasyMesh|Table 17.2.17, Operating Channel Report TLV}}
and the Supported Operating Classes element in
{{bibref|EasyMesh|Table 17.2.19, Client Capability Report TLV}}.
For Multi-Link Operation (MLO) this is the channel over
which association messaging had occurred.
The MAC address of the affiliated STA whose link stats are being
reported.
The total number of bytes transmitted to the affiliated STA.
The total number of bytes received from the affiliated STA.
The total number of packets transmitted to the affiliated STA.
The total number of packets received from the affiliated STA.
The number of packets which could not be transmitted to the
affiliated STA because of errors.
The MAC Address of the logical BSS (BSSID) which is reporting the
failed connection event.
MAC Address identifying the associated device (STA) that has
attempted to connect.
Status Code set to a non-zero value that indicates the reason for
association or authentication failure as defined in
{{bibref|802.11-2020|Table 9-50}}, or Status Code set to zero and
{{param|ReasonCode}} provided.
Reason Code indicating the reason the STA was disassociated or
deauthenticated as defined in {{bibref|802.11-2020|Table 9-49}}.
The time this event happened. Formatted with the date-and-time string
format as defined in {{bibref|RFC3339|Section 3}}.